Specs:

• Firmware: 5.2, supports firmware upgrade
• Voltage: 14-84V (safe for 4-20S)
• Continuous current: 50V/450A; 75V/350A (Values depend on the mounting, ambient temperature and air/water circulation around the device!); Burst: 1200A
• BEC: 5V@1A
• Support Modes: DC, BLDC, FOC (sinusoidal)
• ERPM: 150000
• Communication Ports: USB, CAN, UART, SPI, IIC
• Supported Sensors: ABI, HALL, AS5047, AS5048A
• Input Source Support: PPM, ADC, NRF, UART
• Supported Sensorless: Yes
• Regenerative capacity: Yes
• Programmable via VESC_TOOL: Yes
• Red Switch Button: Yes
• Phase filter: Yes
• Size:227.5*140*54mm(Including Water Cooling Enclosure)

Features:

1.Adjustable protection against: low voltage protection, high voltage protection, over current protection, temperature abnormal protection, mosfets / motor over temperature protection.
2.Support various control modes: Current / Duty cycle / Speed / PID control modes.
3.Support the function of balancing car by connecting the IMU module through the IIC interface; support inertial measurement unit modules such as MPU9250, MPU9150, MPU6050, LSM6DS3, BMI160.
4.CPU:STM32F405 with frequency 168MHz
5.Aluminum PCB with good heat dissipation to expand life span.
6.Built with ignite power on/off switch button.

Wiring Diagram:

Spec:

• Firmware: 6.02 (firmware update supported)
• Size: L103mm*W58mm*H27.7mm
• Voltage:14-84V (4-20S)
• Current:100A Continuous
• BEC:5V@1.5A
• Support BLDC square wave mode control and FOC sine wave mode
• ERPM:150000
• Control Interface Ports:USB,CAN,UART
• Supported Sensors:ABI，HALL，AS5047，AS5048A
• Input Set Support:PPM，ADC，NRF,UART
• Wire Size: 10AWG(75100 Pro)
• Programmable: Yes
• Regenerative Capacity: Yes
• Phase Filter: Yes
• Power Switch Button: Red

Wiring diagram:

Spec:

• Firmware: 6.02, supports firmware upgrade
• Voltage: 14-84V (safe for 4-20S)
• Continuous current: 50V/200A; 75V/150A (Values depend on the mounting,
• ambient temperature and air/water circulation around the device!); Burst: 300A
• BEC: 5V@1A
• Support Modes: DC, BLDC, FOC (sinusoidal)
• ERPM: 150000
• Communication Ports: USB, CAN, UART, SPI, IIC
• Supported Sensors: ABI, HALL, AS5047, AS5048A
• Input Source Support: PPM, ADC, NRF, UART
• Supported Sensorless: Yes
• Regenerative capacity: Yes
• Programmable via VESC_TOOL: Yes
• Size:130x68x41mm
• Motor/power wire size: 8 AWG
• Phase Filter: Yes
• Power Switch Button: Red

Feature:

• Adjustable protection against: low voltage protection, high voltage protection,over current protection, temperature abnormal protection, mosfets / motor over temperature protection.
• Support various control modes: Current / Duty cycle / Speed / PID control modes.
• Support the function of balancing car by connecting the IMU module through the
• IIC interface; support inertial measurement unit modules such as MPU9250,
• MPU9150, MPU6050, LSM6DS3, BMI160.
• CPU:32F405 with frequency 168MHz
• Aluminum PCB with good heat dissipation to expand life span.
• 75200 Pro V2.0 aluminum substrate single drive: supports single serial port function,and integrates Bluetooth module function (convenient to connect Bluetooth parameters and read data in real time),and built with power on/off switch.

Wiring diagram:

Warm tips:

It is recommended to keep firmware 5.2 from factory ship, the new firmware upgrade may damage the ESC.

Remark:Please be careful to limit the Absolute Maximum Current below 200A. HERE

Specs:

• Voltage:14-84V (4-20S)
• Continuous Current:100A
• Max Current:120A
• Firmware: latest (firmware update supported)
• ERPM:150000
• Control Interface Ports:USB,CAN,UART
• BEC:5V@1A
• Phase filter: No
• Modes:DC, BLDC, FOC (sinusoidal)
• Supported Sensors:ABI,HALL,AS5047,AS5048A
• Input Set Support:PPM,ADC,NRF,UART
• Wire Size: 12AWG
• Size:L85mm*W50.7mm*H33.8mm
• Programmable: Yes
• Regenerative Capacity: Yes

Feature:

1. Two COMM ports, UART bluetooth module, IMU,screen display or remote controller supportable.
2. Based on VESC, programmable via vesc_tool with overheat and overcurrent protection.

Wiring diagram：

Detail size:

Video:

Spec:

• Firmware: 6.02 (firmware update supported)
• Voltage:14-75V( safe for 3-16S)
• Continuous Current : 200A
• Max Current :300A
• Supported sensors: ABI, HALL, AS5047,AS5048A
  
• EPRM:150000
• Phase filter: No

Feature:

• Regenerative braking
• Sensored or sensorless operation + hybrid mode
• Configurable RPM-, current-, voltage- and power limits
• Input source: PPM, Analog, NRF Nyko Kama Nunchuck
• Communication ports: USB, CAN, UART
• Throttle curve and ramping for all input sources
• Seamless 4-quadrant operation
• Motor revolution, ampere hour, watt hour counting
• Real-time data analysis and readout through the communication port.
• Adjustable protection against:
• Low input voltage
• High input voltage
• High motor current
• High input current
• High regenerative braking current (separate limits for the motor and the input)
• High RPM (separate limits for each direction)
• Digital VCC and analog VCC are produced by different voltage regulators respectively to make the system AD conversion more accurate
• Motor wire: 8AWG
• Power cable: 10AWG
• Waterproof level(with water cooling enclosure):IP67

Warm tips:

More Detail:

Wiring Diagram With Aluminum Case:

Wiring Diagram With Water Cooling Enclosure: 

Warm tips:

It is recommended to keep firmware 5.2 from factory ship, the new firmware upgrade may damage the ESC.

Specs:

• Firmware: 5.2, supports firmware upgrade
• Voltage: 14-84V (safe for 4-20S)
• Continuous current: 50V/200A; 75V/150A (Values depend on the mounting, ambient temperature and air/water circulation around the device!); Burst: 300A
• BEC: 5V@1A
• Support Modes: DC, BLDC, FOC (sinusoidal)
• ERPM: 150000
• Communication Ports: USB, CAN, UART, SPI, IIC
• Supported Sensors: ABI, HALL, AS5047, AS5048A
• Input Source Support: PPM, ADC, NRF, UART
• Supported Sensorless: Yes
• Regenerative capacity: Yes
• Programmable via VESC_TOOL: Yes
• 75200 Pro Size:130x67.7x39..4mm
• Motor/power wire size: 8 AWG

Features:

1. 75200 aluminum substrate single drive: MOS tube temperature detection is abnormal (minimum display temperature at low temperature is about 30°C)
2. 75200Pro aluminum substrate single drive: MOS tube temperature detection is normal (hardware has been optimized for the problem that the minimum display temperature is about 30°C at low temperature)

3. 75200 aluminum substrate single drive: support dual serial port function
4. 75200Pro aluminum substrate single drive: supports single serial port function, and integrates Bluetooth module function (convenient to connect Bluetooth parameters and read data in real time)

Warm tips:

Wiring diagram：