Please use 5V/2A charger for VX1 Pro (Max. Input voltage of 6.5VDC for VX1 Pro). Do NOT use a charger with an output voltage more than 6.5V, otherwise the VX1 Pro remote controller may be damaged.
Features:
Using 2.4G wireless module-E28-2G4M12S, low power consumption, strong anti-interference ability, long remote control distance
Support 3 speed modes (high gear: red light; middle gear: yellow light; low gear: green light)
Support cruise control mode
Remote control and skateboard battery indicator light
Comfort touch: ABS+Rubber painting surface
Support reverse function
Rechargeable Li-ion Battery (850mAh)
Anti-slip wrist strap
VX1 Remote comes with Receiver
Kindly Reminder ! 1.Please carefully check following receiver connection diagram corresponding with different FSESC, wrong cable collection in reciver side will cause the receiver burned.
2. The variants (for VESC4/ for VESC6 / For Non VESC) only differenciate on reciver cables , the remote is the same one.
1.Supports two-to-one streaming.Includes intelligent noise reduction.Wireless transmission distance within 100 meters.No delay and anti-interference.
2.Two-to-one: record the voices of 2 people at the same time. Supportsthe use of multiple units in the same location.
3. One-to-one: 1transmitter,1 receiver for use with mobile phone anytime,anywhere.
4.Wind screen included. Built for use outdoors,wind resistant,vibration resistant,effective noise reduction.
5.Come with a built in noise reduction microphone. Also supports use of an external microphone.
6.Support stereo or mono recording modes.
7. Real time monitoring and dection of microphone recording conditions.
8.Built in earphone monitoring funtion.
Video:
Anti spark Switch Smart Enhanced 120A for Electric Skateboard /Ebike/ Scooter/Robots
Regular price$32.00
-952 in stock
Spec:
Hardware: V2.2
Max voltage: 12S (50.4V)
Continuous Current: 60A , Max Current: 120A
Burst current: 800A(theoretical current)
Mosfets: NVMFS5C628NLs
LED button diameter:12mm, cable length: 250mm
PCB thickness:4 layers*3oz copper=12oz copper
PCB size: 40mm*32m
Wire:12AWG
Enhanced Features:
High Side Switching -> Much safer to use with multiple ESCs and other devices.
In-rush current limiting.
RC delay network restricts inrush current to safe levels.
dV/dt is ~100V/s (This is considered VERY slow for power electronics. Fast would be 50,000,000V/s). At 6,000 uF output capacitance, this is an inrush current of 600mA.
Smart Power on/off
Roll-to-start. Has 12 second blanking timer after turn off. Can still be turned on by switch during this period.
Auto-turn-off. Will turn off automatically after 20 minutes. The output voltage must vary by at least 500mV within any three second interval to reset the turn-off timer.
Support momentary push button. Hold for 0.3s to turn on, 1s to turn off. Holding it down will cycle it on then off.
High power, 150A Continuous.
Very low idle power draw, ~300uA, will last months on battery.
1.Preventing a small spark may cause explosions in some spark-sensitive areas.
2. Add copper bars for better heat dissipation and over-current flow.
3.Anodized aluminum Heatsink with lots of notches for better heat dissipation.
4.Add silicon glue to fix the LED button cable with the heat shrink.
Warnings:
Do not peel off the heat shrink.There’s no screw to lock the heatsink and PCBA. Only the heat-transfer silicon pad is naturally sticky to heatsink and PCBA.
No short circuit protection, DO NOT short circuit output!
No reverse polarity protection. DO NOT plug in backwards.
Recommended to keep output capacitance under 6,000 uF. Proper operation cannot be guaranteed at higher capacitances.
Do not Hot-Swap. Try to make sure everything is off before connecting and removing. If need be, unplug from battery first, wait for ESCs to turn off, then unplug ESCs. Do the reverse for plugging in, plug in ESCs first before plugging the switch into the battery.
Engineers have thoroughly tested prototypes; however, this is still a new design and a first production run, please exercise extreme caution (as one would normally do with any electric vehicle) when using this device.
Do not attempt to reprogram the MCU unless otherwise advised. Doing so will void any warranty and also put the switch at great risk of failure.
Wiring diagram:
Electric Skateboard Motor Mount For DIY Double Kingpin Trucks
Regular price$29.00
-59 in stock
Spec:
Axle Diameter: 8/10mm
Material: Aluminum Alloy
Color: Black
The detail size of 63 Series motor mount(Axle Diameter:10mm),Suitable for 6354/6374/6384 motors
The detail size of 50 Series motor mount(Axle Diameter: 8MM):(Suitable for H5045/H5055/H5045/H6368 motors,not suitable for 5065 270KV motor )
Package included:
2pcs motor mount
2.4Ghz Remote VX1 for DIY electric skateboard
Regular price$29.00
-331 in stock
Please use 5V/2A charger for VX1 (Max. Input voltage of 6.5VDC for VX1). Do NOT use a charger with an output voltage more than 6.5V, otherwise the VX1 remote controller may be damaged.
Features
2.4Ghz band width
Support 3 speed modes
Support cruise control mode
Remote and E-skateboard power indication lights
Support checking remote battery volume
Comfort touch: ABS+Rubber painting surface
Rechargeable Li-ion Battery
Wrist strap
VX1 Remote comes with Receiver
Function Show
Kindly Reminder !
1.Please carefully check following receiver connection diagram corresponding with different FSESC, wrong cable collection in reciver side will cause the receiver burned.
2. The variants (for VESC4/ for VESC6 / For Non VESC) only differenciate on reciver cables , the remote is the same one.
3. When you choose UART mode connection for VX1 remote receiver, pls do connection after your programming in VESC tool. Or else , it will influence programming. And In UART mode, there is no need to do adjust for remote.
Receiver Connection Diagram
For Single V4
For Dual FSESC4.20: Both hook up with bluetooth and remote receiver
For Single V6
For Dual FSESC6.6 Plus : both hook up with bluetooth and remote receiver
Screen Remote VX2 Pro for Electric skateboard | Ebike | Eboat compatible with VESC
Regular price$43.00
-205 in stock
Please use 5V/2A charger for VX2 (Max. Input voltage of 6.5VDC for VX2). Do NOT use a charger with an output voltage more than 6.5V, otherwise the VX2 remote controller may be damaged.
Features:
Color screen
Option choice for km/h and miles/h
Option choice for FSESC and other VESC( FOCBOX)
2.4Ghz band width
Real time data reading and 0.95OLED display
Support 3 speed modes
Support cruise control mode
Remote and E-skateboard power indication lights
Rechargeable Li-ion Battery
Wrist strap
Battery last for 12 working hours
VX2 Remote comes with Receiver
Shipping: Shipping comes with receiver and cables
Receiver Connection Diagram
For Dual FSESC6.6 Big size :
For Dual FSESC4.20 :
Remark:
1.When plug uart cable , don't need to set up parameters via VESC TOOL, try to set up via screen.
2.The Flipsky VX2 remote just can compatible with base on vesc , if your VESC has changed the program, please choose to purchase carefully.
Function Show
Bluetooth Module 2.4G Wireless Based upon the nrf51_vesc project
Regular price$26.00
-1253 in stock
Based upon the nrf51_vesc project
Kindly Reminder: This bluetooth module support Android /IOS mobile device.
Used to communicating between the VESC and VESC Tool (mobile) over BLE. Note that the UART port on the VESC must be enabled with a baud rate of 115200 for this to work. The UART port on VESC can work only under 115200 baud
Operating voltage: 2.0V ~ 12V Onboard Chip: NRF51822 Actual use distance: The distance to communicate with VESC is about 15 meters Frequency range: 2.4GHz 2.4 GHz multiprotololl RF receiver ARM Cortex-M0 32 bit processor 256kB flash & 16kB RAM PCB size:27mm*13mm 2.0mm seven-pin four-wire connector length:90mm Antenna length:145mm net weight:3.5g
Deep groove ball bearings mainly take radial load, but also can support radial and axial load. When the only radial loads, the contact angle is zero. When the deep groove ball bearings with a larger radial clearance, with angular contact bearings can bear large axial load, deep groove ball bearing friction coefficient is small, the speed limit is also high.
Package included: 1x Deep groove ball bearing
TFT Screen Ver2 Module based on VESC With GPS/Standard
Regular price
Sale price$59.00
-91 in stock
Features:
Compatible with VESC
Compatible with FOCBOX
Volt: 3-12S
Communication port by UART mode
Default Display:
Speed
Current Mileage & Total Mileage
Battery Capacity Percentage, Battery voltage per cell
Upgrade on the base of DAVEga TFT display
TFT Screen Ver2 based on VESC:
This TFT screen display is specially designed for VESC / FOCBOX . And a GPS module is added to display the user's moving speed without using ESCs. At the same time, this module is equipped with ADC throttle, which can directly control ESC acceleration and deceleration. The main page displays real-time speed, current mileage, total mileage, battery power, battery voltage, and the second page includes some parameter settings. as follows:
Display interface
Choose throttle type
Button function:
This module is provided with three buttons K1, K2 and K3. Button functions are as follows:
Kindly remind:
The parameter setting needs to be set according to the actual skateboard motor, wheels, battery and other parameters, so that the speed and mileage displayed on the main page are accurate.
If you want to clear the Trip KM/ Total Trip Km /Riding Time, please re-power on the TFT screen ver2 module, then the reset data can be saved validly.
Electric Skateboard Belt Motor Mount Set For 83/90/97MM Wheel
Regular price
$49.00Sale price$39.00
-152 in stock
Description: Transmission is accurate, no slip at work, with a constant transmission ratio. Smooth transmission, with a buffer, shock absorption capacity, low noise. Easy maintenance, no lubrication, low maintenance costs. Bracket structure design fixed hole position can be adjusted motor 4 fixed screw position, thereby adjusting the size of the belt between the synchronous wheel elastic.
Supported Motors:
6354/6374/6365/63xx
Supported Truck :18mm diameter hangger
Specification: Color: Black Material: Surface oxidation+stainless steel Gear of wheel: 35 tooth Gear of motor: 16 tooth Bore of wheel: 21mm Bore of motor: 8mm/10mm (support motor shaft :8mm / 10mm) Round hole diameter of motor mount: 18mm Motor mount width: 14mm Motor mount length: 131mm Belt width: 11mm Belt length: 270mm Bore of Fixing Plate: 26mm Length of Fixing Plate: 47mm Bolt of the wheel: 7
Package Included:
1 X Pulley For Wheel 1 X Pulley For Motor 1 X Fixing Plate 1 x Bracket 1 X Belt 7 X Bolts 2 X L-key 12 X Screws
MR60 Connector Plug Female And Male Connector 3.5 Bullet Connector 5 Pairs For RC Model Parts /Motor ESC Connection
Regular price$7.90
-290 in stock
Feature:
High Safety Performance:The housings of MR60 connectors could aviod the wire exposing outside, which also aviod the power hurt humans.In addition,MR60 connector with fireproof material pass many certifications,such as UL, CE,ROHS.Last but not least,the production fully passed IOS9001 certification,you totally could use it in safe.
Advanced protective housings:The advanced protective housings of MR60 connector are better than traditional heat shrinks,as using these housings could simplify the welding process,avoiding the wire exposing outside, also make the connector have a good looking
Durable Material:Provides Solid and Reliable Connection,reusable Connector end design for times insert and take off from the Enclosure.With high current indurance performance ,it could be used many times, reach to 1000 times.
Not easy to knock off:100% Genuine Amass Connectors, with Anti-slip plug design,plug more easily,not easy to knock off. Two pcs heat shrinks are also packed with the MR-60 connector together for your backup when you weld some cables.
Wide Application:Often used in remote control aircraft and More RC models, like some big RC lipo battery(MR60 Female), RC ESC(MR60 male) , RC Charger and so on.
Aluminium Case for VESC V4.12 BLDC Motor Controller
Regular price
$39.00Sale price$20.00
75 in stock
Weight:128g
Texture: Aluminum
Colour:Black
CNC machined Aluminium T6 case for BLDC VESC V4.12 Case protects the board from dirt, dust and overheating. Case weights 128g (without board) dimensions :121mmx45mmx21.5mm
package size:20cm*15cm*4cm
The packaging contains: 1pc. Aluminium case 3 plastic Screws +4 metal Screws
Dual ESC Can Bus Connector Compatible with VESC
Regular price$2.40
-681 in stock
DUAL ESC CAN BUS CONNECTOR
Used to connect (2) FLIPSKY ESC units together.
Compatible with VESC®.
Cable length: 250mm
PPM Cable for connection remote receiver with ESC
Regular price$1.80
-46 in stock
A: without connetor:
Dupont Cable Female Jumper
Length:27mm
B: with connector:
Dupont Cable Female Jumper
Connector: JST-PH 3pin 2mm pitch
Length: 24mm
Y Type Cable for Setting up two single ESC for Electric Skateboard
Regular price$6.00
-151 in stock
Connector: Amass Connectors
XT60 for battery cable connection
XT90 for VESC cable connection
Cable
length: 160mm
12AWG copper copil
Electric Skateboard Motor Keyway
Regular price$0.90
-1598 in stock
Spec:
3mm x 3mm x 20mm Steel Keyway (Fit for Flipsky BLDC Belt Motor 6374)
3mm x 3mm x 14mm Steel Keyway (Fit for Flipsky BLDC Belt Motor 6354/6384)
Flipsky D-shape motor pulley electric skateboard motor gear
Regular price$6.90
-690 in stock
Spec:
Name: Motor pulley / Motor Gear
Material : Carbon Steel
Width: 16mm
Tooth: 15T
Pitch: 5mm
For Motor shaft : 8mm / 10mm
What Flipsky motor is fit for 8mm/10mm motor pulley?