Flipsky 12S 200A Smart BMS For ESK8 / Consumer Robot / E-car/ E-board

Applicable battery voltage

• Recommended Battery: 6S-12S
• Operating Voltage Range per Cell: 2V-5V

Charging

• Charging Voltage: 24V-52V
• Charging Current: ≤50A
• Maximum Supported Charging Voltage: 60V
• Minimum Supported Charging Voltage: 14V

Overcharge Protection

• Overcharge Detection Voltage: 2V-5V
• Overcharge Protection Delay: ≥4ms
• Overcharge Release Voltage: 2V-5V

Discharging

• Discharge Current: ≤200A
• Overcurrent Protection for Discharge: ≤200A
• Discharge Voltage: 24V-52V

Overdischarge Protection

• Overdischarge Detection Voltage: 0-5V
• Overdischarge Release Voltage: 0-5V

Overcurrent Protection

• Overcurrent Protection Delay for Discharge: ≥4ms
• Overcurrent Protection Release Condition: Load Disconnect

Short Circuit Protection

• Short Circuit Protection Condition: External Load Short Circuit
• Short Circuit Detection Delay: 320µs
• Short Circuit Protection Release Condition: Load Disconnect

Balancing Current: 86mA @4.2V

Temperature Protection

• Temperature Protection: -20℃ to +120℃

Operating Temperature

• Operating Temperature Range: -20℃ to +80℃

Storage Temperature

• Storage Temperature Range: -20℃ to +100℃

Self-Consumption

• Operating Current: ≤40mA
• Sleep Current: ≤100µA
  

BMS  Details

• Includes: Overcharge Protection, Overdischarge Protection, Overcurrent Protection, Temperature Protection, Battery Capacity Detection, Battery Internal Resistance Detection, Thermal Management, Balancing Function
• Balancing Method: Active Balancing and Passive Balancing
• Short Circuit Protection: External Load Short Circuit
• Short Circuit Protection Recovery: Load Disconnect
• Battery Support: Supports nearly all lithium batteries including Li-ion, Li-polymer, LiFePO4, etc.

BMS Edge

• Compact layout, ultra-mini size.
• Automotive-grade monitoring and balancing IC with independent power supply for enhanced reliability.
• Voltage detection of load, charger, and battery pack.
• Bidirectional current monitoring.
• SOC based on Coulomb counting.
• Humidity sensor and circuit board temperature monitoring.
• Charger circuit detection capability.
• Integrated pre-charge circuit.
• Features power button, USB-Type C, UART, I2C, and isolated CAN bus interfaces.
• Onboard efficient 3.3V regulator powered by the main battery pack.
• Uses high-current capacity automotive-grade screw connectors for main power connection.
• Includes buzzer and LED display.
• Aluminum alloy shell for improved heat dissipation.
• Automotive-grade locking mechanism with reverse interlock to ensure secure connections.
• Compatible with MAXKGO-BMS-TOOL and ENNOID-BMS-TOOL.

BMS Safety Features

• Configurable under-temperature and over-temperature cutoff for charging and discharging.
• Configurable under/over battery voltage cutoff.
• Configurable overcurrent cutoff.
• Configurable minimum pre-charge value.
• High-side load and charger disconnect.
• Transient voltage suppression on all inputs.
• Secondary fuse on all balance channels, USB ports, and power supplies.

Package include：

• 1* PCB board
• 1* HY2.0 single-end 10-pin wire
• 1* HY2.0 single-end 13-pin wire
• 2* GH1.25 single-end 5-pin wire
• 1* GH1.25-5P to DuPont wire adapter
• 1* USB cable, Type-C data cable
• 1* 2.0MM jumper cap
• 1* 1.3-inch OLED display LCD module
• 1* 12MM 3-6V push-button switch
• 4* M5*8 stainless steel round head screws
• 2* M5*12 stainless steel round head screws
• 2* M5 copper nuts
• 6* M5 purple copper washers
• 6* 90-degree angled wire terminals T90-6/5 (purple copper)
• 2* fuses

Wiring diagram(without shell)：

Wiring diagram(with shell)：