High Safety Performance:The housings of MR60 connectors could aviod the wire exposing outside, which also aviod the power hurt humans.In addition,MR60 connector with fireproof material pass many certifications,such as UL, CE,ROHS.Last but not least,the production fully passed IOS9001 certification,you totally could use it in safe.
Advanced protective housings:The advanced protective housings of MR60 connector are better than traditional heat shrinks,as using these housings could simplify the welding process,avoiding the wire exposing outside, also make the connector have a good looking
Durable Material:Provides Solid and Reliable Connection,reusable Connector end design for times insert and take off from the Enclosure.With high current indurance performance ,it could be used many times, reach to 1000 times.
Not easy to knock off:100% Genuine Amass Connectors, with Anti-slip plug design,plug more easily,not easy to knock off. Two pcs heat shrinks are also packed with the MR-60 connector together for your backup when you weld some cables.
Wide Application:Often used in remote control aircraft and More RC models, like some big RC lipo battery(MR60 Female), RC ESC(MR60 male) , RC Charger and so on.
Please use 5V/2A charger for VX1 Pro (Max. Input voltage of 6.5VDC for VX1 Pro). Do NOT use a charger with an output voltage more than 6.5V, otherwise the VX1 Pro remote controller may be damaged.
Features:
Using 2.4G wireless module-E28-2G4M12S, low power consumption, strong anti-interference ability, long remote control distance
Support 3 speed modes (high gear: red light; middle gear: yellow light; low gear: green light)
Support cruise control mode
Remote control and skateboard battery indicator light
Comfort touch: ABS+Rubber painting surface
Support reverse function
Rechargeable Li-ion Battery (850mAh)
Anti-slip wrist strap
VX1 Remote comes with Receiver
Kindly Reminder ! 1.Please carefully check following receiver connection diagram corresponding with different FSESC, wrong cable collection in reciver side will cause the receiver burned.
2. The variants (for VESC4/ for VESC6 / For Non VESC) only differenciate on reciver cables , the remote is the same one.
Anti spark Switch Smart Enhanced 120A for Electric Skateboard /Ebike/ Scooter/Robots
Regular price$32.00
-977 in stock
Spec:
Hardware: V2.2
Max voltage: 12S (50.4V)
Continuous Current: 60A , Max Current: 120A
Burst current: 800A(theoretical current)
Mosfets: NVMFS5C628NLs
LED button diameter:12mm, cable length: 250mm
PCB thickness:4 layers*3oz copper=12oz copper
PCB size: 40mm*32m
Wire:12AWG
Enhanced Features:
High Side Switching -> Much safer to use with multiple ESCs and other devices.
In-rush current limiting.
RC delay network restricts inrush current to safe levels.
dV/dt is ~100V/s (This is considered VERY slow for power electronics. Fast would be 50,000,000V/s). At 6,000 uF output capacitance, this is an inrush current of 600mA.
Smart Power on/off
Roll-to-start. Has 12 second blanking timer after turn off. Can still be turned on by switch during this period.
Auto-turn-off. Will turn off automatically after 20 minutes. The output voltage must vary by at least 500mV within any three second interval to reset the turn-off timer.
Support momentary push button. Hold for 0.3s to turn on, 1s to turn off. Holding it down will cycle it on then off.
High power, 150A Continuous.
Very low idle power draw, ~300uA, will last months on battery.
1.Preventing a small spark may cause explosions in some spark-sensitive areas.
2. Add copper bars for better heat dissipation and over-current flow.
3.Anodized aluminum Heatsink with lots of notches for better heat dissipation.
4.Add silicon glue to fix the LED button cable with the heat shrink.
Warnings:
Do not peel off the heat shrink.There’s no screw to lock the heatsink and PCBA. Only the heat-transfer silicon pad is naturally sticky to heatsink and PCBA.
No short circuit protection, DO NOT short circuit output!
No reverse polarity protection. DO NOT plug in backwards.
Recommended to keep output capacitance under 6,000 uF. Proper operation cannot be guaranteed at higher capacitances.
Do not Hot-Swap. Try to make sure everything is off before connecting and removing. If need be, unplug from battery first, wait for ESCs to turn off, then unplug ESCs. Do the reverse for plugging in, plug in ESCs first before plugging the switch into the battery.
Engineers have thoroughly tested prototypes; however, this is still a new design and a first production run, please exercise extreme caution (as one would normally do with any electric vehicle) when using this device.
Do not attempt to reprogram the MCU unless otherwise advised. Doing so will void any warranty and also put the switch at great risk of failure.
Wiring diagram:
Electric Skateboard Motor Mount For DIY Double Kingpin Trucks
Regular price$29.00
-60 in stock
Spec:
Axle Diameter: 8/10mm
Material: Aluminum Alloy
Color: Black
The detail size of 63 Series motor mount(Axle Diameter:10mm),Suitable for 6354/6374/6384 motors
The detail size of 50 Series motor mount(Axle Diameter: 8MM):(Suitable for H5045/H5055/H5045/H6368 motors,not suitable for 5065 270KV motor )
Package included:
2pcs motor mount
2.4Ghz Remote VX1 for DIY electric skateboard
Regular price$29.00
-336 in stock
Please use 5V/2A charger for VX1 (Max. Input voltage of 6.5VDC for VX1). Do NOT use a charger with an output voltage more than 6.5V, otherwise the VX1 remote controller may be damaged.
Features
2.4Ghz band width
Support 3 speed modes
Support cruise control mode
Remote and E-skateboard power indication lights
Support checking remote battery volume
Comfort touch: ABS+Rubber painting surface
Rechargeable Li-ion Battery
Wrist strap
VX1 Remote comes with Receiver
Function Show
Kindly Reminder !
1.Please carefully check following receiver connection diagram corresponding with different FSESC, wrong cable collection in reciver side will cause the receiver burned.
2. The variants (for VESC4/ for VESC6 / For Non VESC) only differenciate on reciver cables , the remote is the same one.
3. When you choose UART mode connection for VX1 remote receiver, pls do connection after your programming in VESC tool. Or else , it will influence programming. And In UART mode, there is no need to do adjust for remote.
Receiver Connection Diagram
For Single V4
For Dual FSESC4.20: Both hook up with bluetooth and remote receiver
For Single V6
For Dual FSESC6.6 Plus : both hook up with bluetooth and remote receiver