Please use 5V/2A charger for VX1 Pro (Max. Input voltage of 6.5VDC for VX1 Pro). Do NOT use a charger with an output voltage more than 6.5V, otherwise the VX1 Pro remote controller may be damaged.

Features:

• Using 2.4G wireless module-E28-2G4M12S, low power consumption, strong anti-interference ability, long remote control distance
• Support 3 speed modes (high gear: red light; middle gear: yellow light; low gear: green light)
• Support cruise control mode
• Remote control and skateboard battery indicator light
• Comfort touch: ABS+Rubber painting surface
• Support reverse function
• Rechargeable Li-ion Battery (850mAh)
• Anti-slip wrist strap
• VX1 Remote comes with Receiver 

Kindly Reminder !
1.Please carefully check following receiver connection diagram corresponding with different FSESC, wrong cable collection in reciver side will cause the receiver burned.

2. The variants (for VESC4/ for VESC6 / For Non VESC) only differenciate on reciver cables , the remote is the same one.

What are the differences between VX1 and VX1 pro?

Receiver Connection Diagram:

For PPM mode(or Non VESC )

For Dual FSESC4.20 Plus:

For Dual FSESC6.6:

Spec:

• 1.8-inch super clear and big screen display
• Display shows more: Except for basic telemetry data, it also display GPS, motor power, real-time temperature of MOS tube, and throttle progress bar information
• Be compatible with Flipsky FSESC/FTESC and other VESC and Non-VESC
• ESK8 mode / E-surf mode switching freely
• Esurf mode：Cruise speed control function
• Waterproof IP rating: IP67
• Bigger remote battery capacity:1500MA
• ESC failure report ：Detect possible failures of the ESC in time for replacing
• Controller mode: PPM/UART
• Charging way:Wireless Magnetic Charging
• VX3 Pro Remote comes with Receiver (support Flipsky non-vesc)
• Support online upgrade firmware

Feature:

1. Replace the communication module with SX1280;
2. The transmitter microcontroller is replaced with GD32F303CGT6;
3. Add FTESC ESC UART control protocol;
4. Add UART, PPM, UART&PPM control modes;
5. Function switching is changed to joystick up and down switching control;
6. Add gear lock function;
7. Add low battery alarm function for skateboards and surfboards;
8. Add total mileage display function;
9. The maximum wheel diameter can be set to 999mm;
10. Add the function of modifying the default gear at startup;
11. Add whether the cruise mode/reverse function is turned on and can be modified;
12. The maximum number of wheel gears can be set to 999mm;
13. Optimize the screen refresh frame rate and faster data refresh display.

Wiring Diagram:

Please use 5V/2A charger for VX1 (Max. Input voltage of 6.5VDC for VX1). Do NOT use a charger with an output voltage more than 6.5V, otherwise the VX1 remote controller may be damaged.

Features

• 2.4Ghz band width
• Support 3 speed modes
• Support cruise control mode
• Remote and E-skateboard power indication lights
• Support checking remote battery volume
• Comfort touch: ABS+Rubber painting surface
• Rechargeable Li-ion Battery
• Wrist strap
• VX1 Remote comes with Receiver 

Function Show

Kindly Reminder !

1.Please carefully check following receiver connection diagram corresponding with different FSESC, wrong cable collection in reciver side will cause the receiver burned. 

2. The variants (for VESC4/ for VESC6 / For Non VESC) only differenciate on reciver cables , the remote is the same one. 

3. When you choose UART mode connection for VX1 remote receiver, pls do connection after your programming in VESC tool. Or else , it will influence programming. And In UART mode, there is no need to do adjust for remote. 

Receiver Connection Diagram

For Single V4

For Dual FSESC4.20: Both hook up with bluetooth and remote receiver

For Single V6

For Dual FSESC6.6 Plus : both hook up with bluetooth and remote receiver

For PPM mode(or Non VESC )

Manual：VX1_Remote_VX1_product_manual_-20190316.pdf

Please use 5V/2A charger for VX2 (Max. Input voltage of 6.5VDC for VX2). Do NOT use a charger with an output voltage more than 6.5V, otherwise the VX2 remote controller may be damaged.

Features:

• Color screen
• Option choice for km/h and miles/h
• Option choice for FSESC and other VESC( FOCBOX)
• 2.4Ghz band width
• Real time data reading and 0.95OLED display
• Support 3 speed modes
• Support cruise control mode
• Remote and E-skateboard power indication lights
• Rechargeable Li-ion Battery
• Wrist strap
• Battery last for 12 working hours
• VX2 Remote comes with Receiver

Receiver Connection Diagram

For Dual FSESC6.6 Big size :

For Dual FSESC4.20 :

Remark:

2.The Flipsky VX2 remote just can compatible with base on vesc , if your VESC has changed the program, please choose to purchase carefully.

Function Show

Feature:

• 1.6-inch super clear and big screen display
• Display shows more: Except for basic telemetry data, it also display GPS, motor power, real-time temperature of MOS tube, and throttle progress bar information
• Be compatible with Flipsky FSESC and other VESC and Non-VESC
• ESK8 mode / E-surf mode switching freely
• Esurf mode：Cruise speed control function
• Waterproof IP rating: IP67
• Bigger remote battery capacity:1500MA
• ESC failure report ：Detect possible failures of the ESC in time for replacing
• Controller mode: PPM/UART 
• Charging way:Wireless Magnetic Charging
• VX3 Remote comes with Receiver

Remarks: For remote VX3, it is recommended to wash it with fresh water or soak it in fresh water for at least one minute after using to reduce salt residue and extend the service life of the remote.

Wiring Diagram:

Reference video: