Please use 5V/2A charger for VX4 (Max. Input voltage of 6.5VDC for VX4). Do NOT use a charger with an output voltage more than 6.5V, otherwise the VX4 remote controller may be damaged.

Note: USB cable black or white will be shipped randomly.

Feature:

• Color screen(240*240 circular high-brightness LCD screen)
• Option choice for km/h and miles/h
• Option choice for FSESC and other VESC( FOCBOX)
• Use Sx1280 chip,which is based on Loraspread spectrum modulation technology,it has up to 13dB of co-channel rejection.
• Support PPM,Uart,ppm and uart mode.
• Support Remote and receiver upgrade.
• Support 3 speed modes(Default H--high speed)
• Support cruise control mode
• Remote and E-skateboard power indication lights
• Rechargeable Li-ion Battery:1200mAh
• Wrist strap
• VX4 remote comes with receiver

Wiring Diagram:

Detail:

Shipping package:

1pcs VX4 remote

1pcs Uart cable

1pcs PPM cable

1pcs USB TypeC cable

1pcs Manual

Reference video：

Flipsky_VX4_V1.2 firmware and manual download link:

Remark:

1.all these parts in the kit are unassembled when shipment.

2.this All Terrain kit come without motors, it can suitable for flipsky 63 series Motors,recommend motor:6384/6374 /63100 etc . (If you need other KV values, please leave order notes, otherwise 190KV will be sent by default)

Truck:

• Truck Length: 420mm / 16.5''
• Axle Length: 60MM / 2.4''
• Axle Diameter: 10MM

Others：

• hub material: Aluminium Alloy
• Tyre Material: Rubber
• Axle Hole Size:10 mm
• Tyre Pressure: 60PSI 410kpa
• HUB Axle Diameter: 10 mm
• HUB Teeth: 72 teeth
• Pulley teeth:16T HTD5M
• Gear ratio:  72:15
• Belt:445 mm length,15mm width

Detail size:

Package included:

Spec:

• Firmware: 6.02 (firmware update supported)
• Voltage:14-75V( safe for 3-16S)
• Continuous Current : 200A
• Max Current :300A
• Supported sensors: ABI, HALL, AS5047,AS5048A
  
• EPRM:150000
• Phase filter: No

Feature:

• Regenerative braking
• Sensored or sensorless operation + hybrid mode
• Configurable RPM-, current-, voltage- and power limits
• Input source: PPM, Analog, NRF Nyko Kama Nunchuck
• Communication ports: USB, CAN, UART
• Throttle curve and ramping for all input sources
• Seamless 4-quadrant operation
• Motor revolution, ampere hour, watt hour counting
• Real-time data analysis and readout through the communication port.
• Adjustable protection against:
• Low input voltage
• High input voltage
• High motor current
• High input current
• High regenerative braking current (separate limits for the motor and the input)
• High RPM (separate limits for each direction)
• Digital VCC and analog VCC are produced by different voltage regulators respectively to make the system AD conversion more accurate
• Motor wire: 8AWG
• Power cable: 10AWG
• Waterproof level(with water cooling enclosure):IP67

Warm tips:

More Detail:

Wiring Diagram With Aluminum Case:

Wiring Diagram With Water Cooling Enclosure: 

Spec:

• Hardware Version:ODESC4.0/4.1 Single Drive
• PCB layer Number:ODESC4.0/4.1 4 layer*2
• Applicable Voltage: ODESC4.0 8-24V;V4.1 8-56V
• Current Parameter:50A continuous/120A peak
• Support Encoder:Incremental Encoder, Absolute Encoder, Houle Sensor, AMT102, AMT103, TLB5012, AS5047
• Communication Interface:USB-Protocol Open Source (PC, Raspberry Pie, Ros) , UART (Embedded Devices) , PWM (RC Remote) ,STEP/DIRECTION（PLC）、GPIO、CAN、ANALOG INPUT
• Voltage Protection:Programmable Voltage Protection to Prevent Excessive Battery Discharge
• Movement Pattern:Speed Mode, Torque Mode, Current Mode, Position Mode, Trajectory Mode, etc.

Feature:

The ODESC high performance brushless driver is based on the open source project ODrive hardware optimization enhancement, stable performance, and match the original Odriver firmware. The USB connected PC terminal can realize motor debugging and complicated multi-axis control, and can realize FOC control for most brushless motors. With the use of encoder, it can also realize any torque, speed loop, position loop, current loop, and position control based on trajectory planning, can be widely used in flexible robot joints, robotic arms, 3D printing, camera universal joints, pan rail, CNC milling machines, ship models, car models and other DIY, industrial and automation fields.

Wiring Diagram:

ODESC4.0/4.1

Please use 5V/2A charger for VX2 (Max. Input voltage of 6.5VDC for VX2). Do NOT use a charger with an output voltage more than 6.5V, otherwise the VX2 remote controller may be damaged.

Features:

• Color screen
• Option choice for km/h and miles/h
• Option choice for FSESC and other VESC( FOCBOX)
• 2.4Ghz band width
• Real time data reading and 0.95OLED display
• Support 3 speed modes
• Support cruise control mode
• Remote and E-skateboard power indication lights
• Rechargeable Li-ion Battery
• Wrist strap
• Battery last for 12 working hours
• VX2 Remote comes with Receiver

Receiver Connection Diagram

For Dual FSESC6.6 Big size :

For Dual FSESC4.20 :

Remark:

2.The Flipsky VX2 remote just can compatible with base on vesc , if your VESC has changed the program, please choose to purchase carefully.

Function Show