Warm tips:

It is recommended to keep firmware 5.2 from factory ship, the new firmware upgrade may damage the ESC.

Specs:

• Firmware: 5.2, supports firmware upgrade
• Voltage: 14-84V (safe for 4-20S)
• Continuous current: 50V/200A; 75V/150A (Values depend on the mounting, ambient temperature and air/water circulation around the device!); Burst: 300A
• BEC: 5V@1A
• Support Modes: DC, BLDC, FOC (sinusoidal)
• ERPM: 150000
• Communication Ports: USB, CAN, UART, SPI, IIC
• Supported Sensors: ABI, HALL, AS5047, AS5048A
• Input Source Support: PPM, ADC, NRF, UART
• Supported Sensorless: Yes
• Regenerative capacity: Yes
• Programmable via VESC_TOOL: Yes
• 75200 Size:130x67.7x40.1mm(Including alu. case)
• Motor/power wire size: 8 AWG

Features:

1.Adjustable protection against: low voltage protection, high voltage protection, over current protection, temperature abnormal protection, mosfets / motor over temperature protection.
2.Support various control modes: Current / Duty cycle / Speed / PID control modes.
3.Support the function of balancing car by connecting the IMU module through the IIC interface; support inertial measurement unit modules such as MPU9250, MPU9150, MPU6050, LSM6DS3, BMI160.
4.CPU:32F405 with frequency 168MHz
5.Aluminum PCB with good heat dissipation to expand life span.
6.Two COMM ports: UART bluetooth module, screen display or remote controller supportable.

Warm tips:

Wiring diagram：

Warm tips:

It is recommended to keep firmware 5.2 from factory ship, the new firmware upgrade may damage the ESC.

Specs:

• Firmware: Latest Version
• Continuous current: 100A; instantaneous current: 200A
• Voltage: 14V-60V(Cells: 4-13S; safe for 4S to 12S, voltage spikes may not exceed 60V! )
• BEC: 5V@1A
• ERPM: 150000
• Control Interface Ports:USB,CAN,UART
• Supported Sensors:ABI，HALL，AS5047，AS5048A
• Input Set Support:PPM, ADC, NRF, UART, SPI, IIC
• Modes:DC, BLDC, FOC (sinusoidal)
• Regenerative capacity: Yes
• Programmable: Yes
• Motor wire: 10AWG
• Power cable:8AWG
• Size:75.4x63.7x31.1mm(Including heatsink)

Feature:

1. Support four control modes: Current/Dutycycle/Speed /Position control mode.
2. Using 6pcs SFT01N10T high current MOSETS (100V 500A).
3. Protection functions: low voltage protection, high voltage protection, over-current protection, temperature abnormally protection, mosfets over-temperature protection.
4. Support the function of balancing car by connecting the IMU module through the IIC interface; support inertial measurement unit modules such as MPU9250, MPU9150, MPU6050, LSM6DS3, BMI160.

Wiring diagram:

Warm tips:

It is recommended to keep firmware 5.2 from factory ship, the new firmware upgrade may damage the ESC.

Spec:

• Voltage:14-84V( safe for 3-20S)
• Continuous Current : 50V/300A,75V/200A
• Max Current :350A
• Supported sensors: ABI, HALL, AS5047,AS5048A
  
• EPRM:150000
• Size:178*100*45mm((Including the height of water pipes and electrolytic capacitors)

Feature:

• Regenerative braking
• The CPU adopts the 32F405 with the main frequency of 168MHz and the Cortex-M4 architecture with DSP function;
• Sensored or sensorless operation + hybrid mode
• Configurable RPM-, current-, voltage- and power limits
• Input source: PPM, ADC, NRF,UART,PAS
• Communication ports: USB, CAN, UART,SPI,IIC
• Throttle curve and ramping for all input sources
• Seamless 4-quadrant operation
• Motor revolution, ampere hour, watt hour counting
• Real-time data analysis and readout through the communication port.
• Adjustable protection against:
• Low input voltage
• High input voltage
• High motor current
• High input current
• High regenerative braking current (separate limits for the motor and the input)
• High RPM (separate limits for each direction)
• Digital VCC and analog VCC are produced by different voltage regulators respectively to make the system AD conversion more accurate
• Motor wire: 8AWG
• Power cable: 8AWG
• Waterproof level(with water cooling enclosure):IP67

Warm tips:

It is recommended to keep firmware 5.2 from factory ship, the new firmware upgrade may damage the ESC.

Remark:Please be careful to limit the Absolute Maximum Current below 200A. HERE

Specs:

• Voltage:14-84V (4-20S)
• Continuous Current:100A
• Max Current:120A
• Firmware: latest (firmware update supported)
• ERPM:150000
• Control Interface Ports:USB,CAN,UART
• BEC:5V@1A
• Modes:DC, BLDC, FOC (sinusoidal)
• Supported Sensors:ABI,HALL,AS5047,AS5048A
• Input Set Support:PPM,ADC,NRF,UART
• Wire Size: 12AWG
• Size:L85mm*W50.7mm*H33.8mm
• Programmable: Yes
• Regenerative Capacity: Yes

Feature:

1. Two COMM ports, UART bluetooth module, IMU,screen display or remote controller supportable.
2. Based on VESC, programmable via vesc_tool with overheat and overcurrent protection.

Wiring diagram：

Detail size:

Video:

Warm tips:

It is recommended to keep firmware 5.2 from factory ship, the new firmware upgrade may damage the ESC.

Dual FSESC6.6 Plus(Pro swtich) based on Dual FSESC6.6 

Warm tips: please do not remove the shrink to protect the pcb electronics components from impurites or metals which result in short circuit or esc burnt damage.

Upgraded features:

• Pro switch version:
• Power on/off by pressing the button
• Added Can bus connector, be more convenient for 4WD set up
• Changed the USB port soldering process to SMT soldering instead of manual soldering
• Changed the big capacitors to SMT mounting capacitors ,and add more mosfets in the bottom side.

Spec:

- Hardware: V 6.7

- Firmware: Latest firmware version

- Voltage: 8V - 60V (Safe for 3S to 12S LiPo) for the dual ESC

- Voltage spikes may not exceed 60V

- Current: Continuous 100A single, total 200A ,  Instantaneous current 400A per single, total 800A for system instantaneous current. values depend on the mounting  and ambient temperature around the device!

- 5V 1.5A output for external electronics for single

- 3.3V 1A output for external electronics for single

- Modes: DC, BLDC, FOC (sinusoidal)

- Supported sensors: ABI, HALL, AS5047

-ERPM:150000

-Size: 81x77x20mm including heatsink 

-Motor wire: 12AWG

-Power cable:8AWG

-Recommend bullet connectors: 4MM Bullet Connector 

          -Reminder: Detected battery voltage tolerance: +/-0.6V 

The shipping package contains:

• 1*Dual FSESC6.7+Heatsink
• 2*VESC Sensor Wires
• 1*LED button 
• 1*Micro USB
• 1*Manual

Other detail spec is the same with Dual FSESC6.6(big size version, without switch), you can get more information by here:

https://flipsky.net/collections/electronic-products/products/fs-esc-6-6

Dual FSESC6.7 Wiring Diagram:

Set Up diagram

Set up for 4WD 

DUAL FSESC6.7 PLUS SIZE:

Programming Tutorial Reference (VESC tool 1.16)