PRE-SALE: All battle hardened 63100 motor will be ship before May 10th

Spec:

• Weight: 1.4KG
• Max Power: 5500W
• Motor KV: 190
• Max. current: 100A
• Battery type: 4-12S
• Recommend ESC: VESC6
• Torque: 10Nm
• Diameter(mm): 63
• Length(mm): 100
• Total length (mm):130mm(including 8mm round shaft) / 125mm(including 10mm D shaft)
• Shaft(mm): 8mm/10mm
• Bullet connector: 4mm

Detail:

10MM D Shaft Motor Drawings：

8MM Round Shaft Motor Drawings：

Spec:

• Model type: 66112
• Motor dimension: 66*112mm
• Maximum power: 3kw
• Continuous 2kw 
• Motor stator slot: 12
• Shaft:10mm
• Motor pole: 8
• Motor KV:130KV
• Motor Wire: 12AWG wire
• Maximum voltage: 14S
• Maximum current 70A
• No-load current: 2.2A 10V
• Waterproof level:IP68
• Weight:1.4kg

The thrust under the condition of reaching this voltage and current as below:

• 48.5v 2.7A 5kg
• 48.5v 8.2A 10kg
• 48.5v 18.2A 15kg
• 48.5v 20A 17kg
• 48.5v 25A 19kg
• 48.5v 30A 21kg
• 48.5v 35A 23kg
• 48.5v 40A 24kg
• 48.5v 51A 27kg

Drawing:

Spec:

• Weight: 1.4KG
• Max Power: 5000W 
• Motor KV: 140
• Motor Wind: 9
• Idle current: 1.9A at 10V
• Motor Resistance: 0.031Ohm
• Motor inductance: 77uh
• Max. current: 100A
• Battery type: 4-14S
• Recommend ESC: VESC6
• Torque: 10Nm
• Diameter(mm): 63.4
• Length(mm): 103
• Total length (mm):135.5(including shaft)
• Shaft(mm): 8mm/10mm with keyway 
• Bullet connector: 4mm

Motor Diagram:

Product Spec:

• Max Power: 4000 Watts
• Max Current: 95 Amps
• Max Volts: 4-13S 
• Max Torque: 9Nm
• Motor Resistance: 0.05Ohm
• Recommend ESC:VESC4&VESC6(3-12S )
• Weight: 1100g
• The motor length:84mm
• The motor diameter: 63mm
• Shaft Diameter 8mm, 30mm length
• Motor Wire:  12AWG wire with 4.0mm Gold Bullet Connector Male.customizable 5.5mm gold plated connector
  • Wire configuration:
    • Blue = A
    • Black = B
    • Yellow = C
• Stator: 0.2mm thickness lamination japan steel
• Magnet: N42SH high temp curve magnet
• BLDC Motor
• The number of pole: 14

More Detail:

Drawing:

Reference Video:

Feature:

• KV: 140/190KV
• Max Power: 3500Watts
• Max Current: 85 Amps
• Max Volts: 12S 
• Max Torque: 8Nm
• Motor Resistance: 0.05Ohm
• Recommend ESC: 3-12S 50A (FSESC4.12 50A or FSESC 6.6 60A)
• The number of pole: 14
• Net weight: 980g
• Motor wire:12AWG
• Shaft size : 8mm/10mm

Reference Information:

• The screws used for the motor are M4 metric bolts. Using our motor mounts, we recommend using M4 Socket Cap bolts.
• Screws to mount the motor are not included with the motor.
• If you choose round shaft motor, shipping includes the key for the keyway
  
• If you choose the shipping comes with pulley, will come with 8mm steel material pulley.
• The Flipsky logo is in different places, will be shipped randomly.

  
  

More details:

Round Shape Shaft Drawing（108mm length）: 

D-Shape Shaft Drawing(99 mm length）: 

Reference Video:

Spec

• Max Power: 2450 Watts
• Max Current: 65 Amps
• Max Volts: 12S 
• Max Torque: 7Nm
• Motor Resistance: 0.053Ohm 
• Recommend ESC: 3-12S 50A (FSESC4.12 50A or FSESC 6.6 60A)
• Weight: 1.23 lb / 0.56 kg
• The motor length:54mm
• The motor diameter: 63mm
• Shaft diameter: 10mm D Shaft ,24mm length/8mm Round-short shaft,24mm length/8mm Round-long shaft,30mm length
• Motor Wire: 320mm silicone 12AWG wire with 4.0mm Gold Bullet Connector Male.
  • Wire configuration:
    • Blue = A
    • Black = B
    • Yellow = C 
• BLDC Motor
• The number of pole: 14

Reference Information:

• The screws used for the motor are M4 metric bolts. Using our motor mounts, we recommend using M4 Socket Cap bolts.
• Screws to mount the motor are not included with the motor.

Difference Long Shaft and Short shaft ：

More Detail:

6354 10MM D Shaft Motor Drawing:

6354 8MM Round-Short Shaft Motor Drawing:

6354 8MM Round-Long Shaft Motor Drawing:

Remark: This product will not come with cable . 

Features:

• Type: Underwater Propeller Motor
•  Motor dimension: 50*85mm
• Waterproof level:IP28 grade waterproof
• Weight:1.51b/0.68kg

Rerference information:

Product Spec:

• Voltage range: 6-20S (25.2-84V)

• Max Spin Speed(RPM): 16380

• KV(RPM/V): 120KV/100KV

• Max Power:6000W

• Peak current: 200A

• The number of pole: 6

• Max torque at 60%:9NM

• Demension: D65*L161mm

• Max working temperature: 120︒C

• Insulation voltage & leak current: AC500V/10MA/3S

• Lead wires extension: 8AWGx1300mm

• Waterproof level:IP68

• Weight:3kg

• Plug: 8.0mm       

• Motor wire: 8AWG

Package inclued:

1*FS65161 ( 100KV or 120KV)

1*Propeller

3*8.0mm bullet connectors

Why upgrade from oil sealed to water/ceramic sealed)?

Add a ceramic ring in the middle, reduce the direct contact between the sealing ring and the bearing, extend the life of the bearing; improve the waterproof performance

Update Detail:

Water-seal has 2 parts as the following pictures
2 strong hardness ceramic run with each other and metal ring part spins together with shaft&ball bearing,
which can prevent the abration between shaft and water-seal, extend the motor lifespan with better IP rate.

12mm shaft with M8x1.25 thread (Sensorless)

Application:

Efoil, Electric surfboard, Electric Hydrofoil,Foilsurf,Surffoil, RC Boat, Esurf, Jetski, Jetboard, etc.,

Product Spec:

• Max Power: 4000 Watts
• Max Current: 95 Amps
• Max Volts: 4-13S 
• Max Torque: 9Nm
• Motor Resistance: 0.05Ohm
• Recommend ESC:VESC4&VESC6(3-13S )
• Weight: 1000g
• The motor length:84mm
• The motor diameter: 63mm
• Shaft Diameter 8mm/10mm, 30mm length(8mm ), 25mm length(10mm),3x3x14mm keyway slot.
• Motor Wire:  12AWG wire with 4.0mm Gold Bullet Connector Male.customizable 5.5mm gold plated connector
  • Wire configuration:
    • Blue = A
    • Black = B
    • Yellow = C
• Stator: 0.2mm thickness lamination japan steel
• Magnet: N42SH high temp curve magnet
• BLDC Motor
• The number of pole: 14

Sensor Wire: Standard RC Sensor Wire JST-ZH 6pin 1.5mm/2mm pitch

• Internal PCB with 120 Degree Hall Effect Sensors.
• Motor can be used with or without a sensor. Sensorless operation is most common.
• VESC Sensor Wires required to use with VESC.

What's Our Product Feature?

• Stator: Lamination Japan steel
• 12awg high strand silicone wire with 4.0mm gold bullet connectors.
• Both support sensor and sensorless mode! 

The 6384 motor 8mm shaft come with 8mm motor pulley is 20mm width, 10mm shaft come with 10mm motor pulley is 17mm width:

8mm shaft diagram:

 10mm shaft diagram:

Features:

• KV:160KV
• Max Volts:12S
• Rated voltage:24V
• No-load current:＜ 1A
• Maximum load current:30A
• Rated power :500W
• Motor dimension: 50*62mm
• Thrust ：5KG
• Current:12A
• Hole distance:φ 35
• Screw holes:4×M4
• Waterproof Level :IP68
• Motor wire: 12AWG

What is Advantages of Flipsky 5062 motor:

• Applying high thermal conductive material into the vacuum glue sealing coil for waterproof treatment, which can protect the copper wire and silicon steel sheet from seawater corrosion effectively.
• Adopting special stainless steel bearing and lubricating grease. Salt spray test can reach 144 hours.
•  The upper and lower positions of the magnets have the rings to lock the magnets and prevent the magnet from falling off.
• The motor shaft is made of 316 stainless steel, which can work in seawater for a long time.
•  The solder joints of the motor leads are potted inside the motor, which can meet the 200m suppression test.

Motor Spec:

• Product Name: 42 two-phase stepper motor
• Model number :17HS4401
• Step angle : 1.8 °
• Maximum no-load starting frequency : ≥ 1400 PPS
• Rated voltage 3.6V
• Maximum no-load operating frequency : ≥ 4000 PPS
• Rated current : 1.5A / phase
• Phase inductance :3.7 × (1 + 20%) mH
• Holding torque : ≥420 mN.m
• Phase resistance : 2.4 × (1 + 15%) Ω / phase
• Positioning torque : 15 mN.m REF
• Electric strength : AC600V / 1mA / 1S
• Motor wire: 20AWG

Wiring Instructions:

1. VCC : Connect 12-30V power supply ( Refer to the working voltage of the motor, general 24V )
2. GND: Ground wire
3. CLK : Control signal (Connected to pulse input )
4. DIR: Direction control signal ( Floating forward, ground reverse )
5. ENA: Connect to enable signal ( Default enable, grounding stops working )
6. P2: Connect one phase to the motor on each side ( Refer to the motor parameter description,   the motor is divided into two phases AB, pins 1 and 2 are connected to one phase, and pins 3 and 4 are connected to the other phase. )

1.Div1, Div2 control pulse frequency division

(1) 00: 4 subdivision

(2) 10: 8 subdivision

(3) 01:16 subdivision

(4) 11:32 subdivision

2.Ctl setting control mode, open-loop / closed-loop

(1) 0 : Open-loop mode

(2) 1 : Closed-loop mode

3.AC setting calibration

Turn the AC to position 1, and turn on the power. The LED blinks 3 times to start automatic calibration. The motor shaft rotates counterclockwise for one cycle and then clockwise for one cycle. The system automatic calibration complete and the LED continues to flash. The AC dial returns to position 0, and then restart power.

The advantage of 42 Stepper Motor:

Application examples:

• 3D printing with fine closed-loop positioning
• Optical precision aiming (Laser, telescope, camera gimbal, etc.)
• Speed loop record player
• Force feedback / impedance control robot
• Force feedback of game controller
• Adjustable mechanical impedance: virtual spring, damper, etc.
• Electric transmission device between two axes such as CNC machine tools
• Gravity elimination (eg: offset gravity torque on the robot arm, etc.)
• Load detection and feature description (Used as a balance, etc.)
• Paper towel / TP distributor
• Variable load (Brake, generator, etc.)
• Valve control (Automated garden hose, etc.)

Detail:

H5065 Motor Spec:

SHAFT: Diameter 8mm （Recommended: Flipsky 8mm D-shape motor pulley）

Torque:1.2NM

Shipping Package:

1*H5065 motor

1* free vesc sensor wire

H5065 Motor Outline Drawing:

Features:

• Waterproof level:IP28 grade,it can work underwater.
• Material :316 stainless steel shaft

Spec:

• Maximum power:410W
• Motor diameter: 46mm
• Motor length: 50mm
• Mounting distance: 28mm
• Shaft diameter: 4.85mm
• Prop mounting distance: 25mm
• Weight:310g

What is the advantage of F4125：

1. Anti-corrosion, can be used in sea water.
2. IP28 grade waterproof, It can work underwater.

Product Spec:

Max Power: 1720W
Max Current: 48A
Max Volts: 12S
Max Torque:2.2 N.m
Recommend ESC: 3-12S 50A (FSESC4.12 50A or FSESC 6.6 60A)
Weight: 1.64 lb / 0.745 kg
The motor length:68mm
The motor diameter: 63mm
SHAFT: Diameter 10mm, 25mm length (Recommended: Flipsky 10mm D-shape motor pulley)
Motor Wire: 300mm silicone 14AWG wire with MT60 male connector.
Wire configuration:
Blue = U
White = V
Yellow = W

BLDC Motor
The number of pole: 14
Sensor Wire: Standard RC Sensor Wire HY2.0-5P connector

Shipping package:

1* H6368 motor(Two design, will ship random.)

1* free VESC sensor wire

Diagram:

Product Spec:

Max Power: 1620W
Max Current: 45A
Max Volts: 12S
Max Torque:1.9N.m
Recommend ESC: 3-12S 50A (FSESC4.12 50A or FSESC 6.6 60A)
Weight: 1.259 lb / 0.572 kg
The motor length:55mm
The motor diameter: 63mm
SHAFT: Diameter 10mm, 25mm length
Motor Wire: 300mm silicone 14AWG wire with MT60 male connector.
Wire configuration:
Blue = U
White = V
Yellow = W

BLDC Motor
The number of pole: 14
Sensor Wire: Standard RC Sensor Wire HY2.0-5P connector 

Shipping Package:

1*H6355(6354) Motor( two design, will ship radom)

1* free VESC sensor wire

Diagram:

Product Spec:

• Max Power: 1150W
• Max Current: 32A
• Max Volts: 12S
• Max Torque: 0.85 N.m
• Recommend ESC: 3-12S 50A (FSESC4.12 50A or FSESC 6.6 60A)
• Weight: 0.74 lb / 0.34 kg
• The motor length:48.6mm
• The motor diameter: 49.5mm                                                                                       
• No-load current：0.4A                                                                                                       
• The internal resistance：0.11 ohm
• SHAFT: Diameter 8mm, 25mm length （Recommended: Flipsky 8mm D-shape motor pulley）
• Motor Wire: 300mm silicone 16AWG wire with MT30 male connector.
• Wire configuration:
• Blue = U
• White = V
• Yellow = W

• The number of pole: 14
• Sensor Wire: Standard RC Sensor Wire HY2.0-5P connector

Shipping package：

1* H5045 Motor

1* free VESC sensor wire 

• Max Power: 3250 Watts
• Max Current: 85 Amps
• Max Volts: 12S 
• Max Torque: 8Nm
• Motor Resistance: 0.05Ohm
• Recommend ESC: 3-12S 50A (FSESC4.12 50A or FSESC 6.6 60A)
• Weight: 1.9 lb / 0.86 kg
• The motor length:74mm
• The motor diameter: 63mm
• SHAFT: Diameter 8mm, 32mm length, 3x3x20mm keyway slot.
• Motor Wire: 130mm silicone 12AWG wire with 4.0mm Gold Bullet Connector Male.
  • Wire configuration:
    • Blue = A
    • Black = B
    • Yellow = C
• Stator: 0.2mm thickness lamination japan steel
• Magnet: N42SH high temp curve magnet
• BLDC Motor
• The number of pole: 14

Sensor Wire: Standard RC Sensor Wire JST-ZH 6pin 1.5mm pitch

• Internal PCB with 120 Degree Hall Effect Sensors.
• Motor can be used with or without a sensor. Sensorless operation is most common.
• VESC Sensor Wires required to use with VESC.

Shipping

• 6374 190KV EPOWER Motor (Fits 63mm Motor Mount)
• If you choose with motor pulley, will ship steel material

What's Our Product Feature?

• Stator: Lamination Japan steel
• 12awg high strand silicone wire with 4.0mm gold bullet connectors.
• Both support sensor and sensorless mode! 

Reference Information

• The screws used for the motor are M4 metric bolts. Using our motor mounts, we recommend using M4 Socket Cap bolts.
•  Screws to mount the motor are not included with the motor.
• The key for keyawy is included with motors for shipping
• The mechanical diagram: