Using 2.4G wireless module-E28-2G4M12S, low power consumption, strong anti-interference ability, long remote control distance
Support 3 speed modes (high gear: red light; middle gear: yellow light; low gear: green light)
Support cruise control mode
Remote control and skateboard battery indicator light
Comfort touch: ABS+Rubber painting surface
Support reverse function
Rechargeable Li-ion Battery (850mAh)
Anti-slip wrist strap
VX1 Remote comes with Receiver
Kindly Reminder ! 1.Please carefully check following receiver connection diagram corresponding with different FSESC, wrong cable collection in reciver side will cause the receiver burned.
2. The variants (for VESC4/ for VESC6 / For Non VESC) only differenciate on reciver cables , the remote is the same one.
Display shows more: Except for basic telemetry data, it also display GPS, motor power, real-time temperature of MOS tube, and throttle progress bar information
Be compatible with Flipsky FSESC and other VESC and Non-VESC
ESK8 mode / E-surf mode switching freely
Esurf mode:Cruise speed control function
Waterproof IP rating: IP67
Bigger remote battery capacity:1500MA
ESC failure report :Detect possible failures of the ESC in time for replacing
Controller mode: PPM/UART
Charging way:Wireless Magnetic Charging
VX3 Remote comes with Receiver
Remarks: For remote VX3, it is recommended to wash it with fresh water or soak it in fresh water for at least one minute after using to reduce salt residue and extend the service life of the remote.
Wiring Diagram:
Reference video:
Anti spark Switch Smart Enhanced 200A for Electric Skateboard /Ebike/ Scooter/Robots
Regular price
$55.00Sale price$39.00
-720 in stock
Spec:
Hardware: V2.2
Max voltage: 13S (60V)
Continuous Current: 150A , Max Current: 200A
Mosfets: NVMFS5C628NLs
LED button diameter:12mm, cable length: 250mm
PCB thickness:4 layers*3oz copper=12oz copper
PCB size: 40mm*32m
Enhanced Features:
High Side Switching -> Much safer to use with multiple ESCs and other devices.
In-rush current limiting.
RC delay network restricts inrush current to safe levels.
dV/dt is ~100V/s (This is considered VERY slow for power electronics. Fast would be 50,000,000V/s). At 6,000 uF output capacitance, this is an inrush current of 600mA.
Smart Power on/off
Roll-to-start. Has 12 second blanking timer after turn off. Can still be turned on by switch during this period.
Auto-turn-off. Will turn off automatically after 20 minutes. The output voltage must vary by at least 500mV within any three second interval to reset the turn-off timer.
Support momentary push button. Hold for 0.3s to turn on, 1s to turn off. Holding it down will cycle it on then off.
High power, 150A Continuous.
Very low idle power draw, ~300uA, will last months on battery.
1.Preventing a small spark may cause explosions in some spark-sensitive areas.
2. Add copper bars for better heat dissipation and over-current flow.
3.Anodized aluminum Heatsink with lots of notches for better heat dissipation.
4.Add silicon glue to fix the LED button cable with the heat shrink.
Warnings:
Do not peel off the heat shrink.There’s no screw to lock the heatsink and PCBA. Only the heat-transfer silicon pad is naturally sticky to heatsink and PCBA.
No short circuit protection, DO NOT short circuit output!
No reverse polarity protection. DO NOT plug in backwards.
Recommended to keep output capacitance under 6,000 uF. Proper operation cannot be guaranteed at higher capacitances.
Do not Hot-Swap. Try to make sure everything is off before connecting and removing. If need be, unplug from battery first, wait for ESCs to turn off, then unplug ESCs. Do the reverse for plugging in, plug in ESCs first before plugging the switch into the battery.
Engineers have thoroughly tested prototypes; however, this is still a new design and a first production run, please exercise extreme caution (as one would normally do with any electric vehicle) when using this device.
Do not attempt to reprogram the MCU unless otherwise advised. Doing so will void any warranty and also put the switch at great risk of failure.
Wiring diagram:
Electric Skateboard Motor Mount For DIY Double Kingpin Trucks
Regular price$29.00
-32 in stock
Spec:
Axle Diameter: 8/10mm
Material: Aluminum Alloy
Color: Black
The detail size of 63 Series motor mount(Axle Diameter:10mm),Suitable for 6354/6374/6384 motors
The detail size of 50 Series motor mount(Axle Diameter: 8MM):(Suitable for H5045/H5055/H5045/H6368 motors,not suitable for 5065 270KV motor )