Please be careful to limit the Absolute Maximum Current below 250A,setting page

Specs:

• Size:L107mm*W103mm*H18.5mm
• Voltage:14-84V (4-20S safe)
• Current:continuous max 100A single,dual continuous max 200A,values depend on the mounting  and ambient temperature around the device!
• BEC:5V@1A
• Support BLDC square wave mode control and FOC sine wave mode
• Firmware: latest (firmware update supported)
• ERPM:150000
• Control Interface Ports:USB,CAN,UART
• Supported Sensors:ABI，HALL，AS5047，AS5048A
• Input Set Support:PPM，ADC，NRF,UART
• Wire Size: 12AWG
• Programmable: Yes
• Regenerative Capacity: Yes

Warm tips:

Detail:

Features:

• Using 2.4G wireless module-E28-2G4M12S, low power consumption, strong anti-interference ability, long remote control distance
• Support 3 speed modes (high gear: red light; middle gear: yellow light; low gear: green light)
• Support cruise control mode
• Remote control and skateboard battery indicator light
• Comfort touch: ABS+Rubber painting surface
• Support reverse function
• Rechargeable Li-ion Battery (850mAh)
• Anti-slip wrist strap
• VX1 Remote comes with Receiver 

Kindly Reminder !
1.Please carefully check following receiver connection diagram corresponding with different FSESC, wrong cable collection in reciver side will cause the receiver burned.

2. The variants (for VESC4/ for VESC6 / For Non VESC) only differenciate on reciver cables , the remote is the same one.

What are the differences between VX1 and VX1 pro?

Receiver Connection Diagram:

For PPM mode(or Non VESC )

For Dual FSESC4.20 Plus:

For Dual FSESC6.6:

Transmitter specs:

• Number of channels:100
• Number of channel groups:1 and 2
• Frequency range:550MHz-590MHz ,antenna 1/4 wavelength
• Audio output level-10dB.
• Headphone output level 87mW(32 Ohms)
• Receiving sensitivity-95 dB
• Signal-to-noise ratio≥90 dB,sound delay 1ms.
• Frequency response 40Hz-18kHz(+/-3dB)
• Reference deviation ±5kHz(-60dBV,input 1kHz)
• Distortion ≤0.5
• Battery type: Lithium battery
• Working temperature 0°C-50°C
• Storage temperature-20°C-55°C

Receiver specs:

• Number of channels: 50
• Numberof channels group:2
• Frequency range :550MHz-590MHz,SNR≥90dB
• Spurious suppression-60dB
• Transmission power 40mW,sound delay 1ms,antenna 1/4 wavelength.
• Reference deviation ±5kHz(-60dBV,input 1kHz)
• Distortion ≤0.5
• Reference audio input level-40dB(Microphone input, 0dB attenuation)
• Battery type: Lithium battery
• Working temperature 0°C-50°C
• Storage temperature-20°C-55°C

Features:

1.Supports two-to-one streaming.Includes intelligent noise reduction.Wireless transmission distance within 100 meters.No delay and anti-interference.

2.Two-to-one: record the voices of 2 people at the same time. Supportsthe use of multiple units in the same location.

3. One-to-one: 1transmitter,1 receiver for use with mobile phone anytime,anywhere.

4.Wind screen included. Built for use outdoors,wind resistant,vibration resistant,effective noise reduction.

5.Come with a built in noise reduction microphone. Also supports use of an external microphone.

6.Support stereo or mono recording modes.

7. Real time monitoring and dection of microphone recording conditions.

8.Built in earphone monitoring funtion.

Video:

Firmware & software repositories are available click here:Github page.

Spec:

• Cell voltage operating range:2V-5V
• Recommended series cell:6S-12S
• Charge / discharge voltage:24V-52V
• Charge Current：≤20A
• Abs. Max battery voltage: 60V
• Minimum operating voltage: 14V
• Continuous charging current: 20A
• Over charge detect and release voltage: 2V-5V
• Over charge protection delay: ≥4ms
• Discharge current: ≤70A
• Max. Continuous discharge / regen current: 70A 
• Over discharge detect / release voltage: 0-5V
• Over current detect delay:≥4ms
• Discharge over current protection release condition: off load
• Short Circuit detect voltage:short circuit of external load
• Short Circuit detect delay: 320us
• Short Circuit protection release: off load
• Battery pack capacity and internal resistance detection: Yes
  
• Balance current: 86mA @4.2V
• Temp Protect: -20℃—+120℃
• Working Temp Range:-20℃—+80℃
• Storage Temp Range: -20℃—+100℃
• Working current: ≤40mA
• Sleeping current: ≤100uA
• Size: 89 x 40 x 20.8mm
• Net weight: 106.5g
• Packing size: 140 x110 x 50 mm
• Package weight: 303.5g
• Including outer carton size: 170*120*100mm
• Weight with outer carton: 380g

Feature:

• Compact layout and mini
• Using aluminum alloy material shell, better heat dissipation.
• Automotive grade design, automotive grade locking connector.
• Configuring and firmware upgrades over USB through the MAXKGO-BMS-TOOL and ENNOID-BMS-TOOL.
• Automotive grade monitoring & balancing IC with separate power supply for increased reliability
• Voltages measurements for load, charger & battery pack
• Bi-directional current monitoring
• SOC based on coulomb counting
• Humidity sensor & board temperature monitoring
• Charger detection circuit
• Integrated precharge circuit
• Power button, USB-C, UART, I2C & isolated CAN bus interface
• On board High-Efficiency 3.3V regulator powered from the main battery pack
• High current capacity automotive grade screw connectors for main power connections
• Buzzer & status LED
• Support overcharge/discharge/over current /temperature protection,and have thermal management/balance function(active balance and passive balance).
• Support almost all lithium batteries such as lithium ion battery, lithium polymer battery, lithium phosphate battery, etc.

 Video:

Firmware & software repositories are available click here:Github page.

Spec:

• Cell voltage operating range:2V-5V
• Recommended series cell:18S-24S
• Charge Voltage:48V-104V
• Charge Current：≤10A
• Abs. Max battery voltage: 120V
• Minimum operating voltage: 28V
• Continuous charging current: 10A
• Over charge detect and release voltage: 2V-5V
• Over charge protection delay: ≥4ms
• Discharge current: ≤70A
• Max. Continuous discharge / regen current: 70A
• Discharge voltage:48V-104V
• Over discharge detect and release voltage: 0-5V
• Over current detect delay:≥4ms
• Discharge over current protection release condition: off load
• Short Circuit detect voltage:short circuit of external load
• Short Circuit detect delay: 320us
• Short Circuit protection release: off load
• Battery pack capacity and internal resistance detection: Yes
• Balance current: 50mA @4.2V
• Temp Protect: -20℃—+120℃
• Working Temp Range:-20℃—+80℃
• Storage Temp Range: -20℃—+100℃
• Working current: ≤40mA
• Sleeping current: ≤100uA
• Size: 109 x 40mm
• Net weight: 126.7g
• Packing size: 140 x110 x 50 mm
• Package weight: 370.3g
• Including outer carton size: 170*120*100mm
• Weight with outer carton: 420g

Feature:

• Compact layout and mini
• Using aluminum alloy material shell, better heat dissipation.
• Automotive grade design, automotive grade locking connector.
• Configuring and firmware upgrades over USB through the MAXKGO-BMS-TOOL and ENNOID-BMS-TOOL.
• Automotive grade monitoring & balancing IC with separate power supply for increased reliability
• Voltages measurements for load, charger & battery pack
• Bi-directional current monitoring
• SOC based on coulomb counting
• Humidity sensor & board temperature monitoring
• Charger detection circuit
• Integrated precharge circuit
• Power button, USB-C, UART, I2C & isolated CAN bus interface
• On board High-Efficiency 3.3V regulator powered from the main battery pack
• High current capacity automotive grade screw connectors for main power connections
• Buzzer & status LED
• Support overcharge/discharge/over current /temperature protection,and have thermal management/balance function(active balance and passive balance).
• Support almost all lithium batteries such as lithium ion battery, lithium polymer battery, lithium phosphate battery, etc.

Video:

Remark: Without strip option default ship 12V LED Strip Controller.

Specs:

• Voltage: 4.5V-5.5V
• Minimum current: 0.5A
• Operating temperature: -40-85°C
• Optimum humidity: 85%RH
• Connection method: WIFI radio
• ESC Compatible: VESC, FSESC, FOC
• LED Strip Support: APA102,WS2801,WS2811,WS2812,WS2813,WS2815 LED Strip
• RAM: standby status with 3 modes; running status with 8 modes; braking status with 8 modes
• LED2811: 60 leds/m, 5050 RGB,1meter
• LED2812: 144 leds/m,5050 RGB,1meter
• LED2813: 30 leds/m, 5050 RGB,1meter
• LED2815: 30 leds/m, 5050 RGB,1meter
• Color mode: custom available
• Size: 34mm x 39mm x 10mm
• N.W.: 11.8g

Features:

1. It’s designed for sports vehicles, compatible with vesc, fsesc, foc escs for esk8 electric skateboards, ebike, escooter etc.
2. Adopting high-speed single-chip microcomputer to process data without delay or intermittence.
3. With 3 different status: standby, braking and running status. Multiple modes choices: standby status*3 modes; running status*8 modes; braking status*8 modes
4. Mobile WiFi control available: customers can change status, strip colors and speed via mobile phone, convenient for customers control.
5. The led strip controller comes with a stop-down power module, which can reduce the vibration effects during the running process.

Wiring:

ESK8 Sport LED Strip Controller Manual

Reference video: