flipsky_esc_tool  software and manual download link

Spec:

• Firmware: V1.3 or above (firmware update via Flipsky ESC Tool supported)
• Voltage: 14V-84V (safe for 4S-20S)
• Continuous current: 50V/550A; 75V/450A (Values depend on the mounting, ambient temperature
• and air/water circulation around the device!);
• Peak Current: 1000A
• BEC:5V@1A
• Motor/power Wire Size:8 AWG (3pcs combine)
• Programmable Tool: Flipsky ESC TOOL
• PWM Frequency Control: YES
• Multiple Speed Gear Limit Control:YES (UART / ADC)
• Regenerative Capacity: Yes
• Communication Ports: USB, CAN, UART, PPM, ADC
• Input Signal Support: PPM, ADC, UART (compatible with FLIPSKY remote VX4 and VX3Pro
• only at present, it will be compatible with more remote controllers soon)
• Startup Modes Support: IPDS (sensorless), HFPI (sensorless), HALL (sensored)
• Multiple Speed Gear levels: Low, Medium, High, Reverse
• Switch Support: Power on/off button switch or key switch
• Size: L227.5*W140*H54mm(with water cooling enclosure)

Features:

1. Adopting CPU AT32F403ARCT7 with the structure of ARM Cortex-M4 allows CPU clock speed.
2. 240MHz and the max PWM switching frequency 45KHz, which improves the motor RPM.
3. Programmable via Flipsky ESC Tool to be compatible with multi-types of motor, different
4. batteries voltages and many control ways.
5. Programmable via Flipsky VX4 remote (Firmware Version:VX4_V1.2.1or above)
6. Supporting FOC with low working noise and smooth starting.
7. Supporting Real-time data and fault alerts.
8. Supporting adaptive variable PWM frequency control.
9. Supporting sensor mode(HALL) and sensorless modes (IPDS, HFPI).
10. Supporting control types: Current, Duty Cycle.
11. Protection functions: low and high voltage protection, motor over-temperature protection (suitable
12. for NTC-10K-25℃ temperature sensing resistance only), battery over discharge protecting,
13. mosfets over current and over-temperature protection.

Spec:

• Size: ∅ 65*150mm
• KV:160KV
• Voltage range: 4-13S
• Rated current: 30A;Maximum current:70A
• Insulation current:AC500v/1ma/3s
• Rated power:1500W;Maximum power:3000W
• Rated torque:2.3N.m;Maximum torque 4.5N.m
• Internal structure:12N/10p
• ESC drive mode:PPM
• Communication port: USB
• ESC driver firmware:5.2 vesc tool 3.00
• ESC support mode: BLDC/FOC
• Shaft specifications ∅ 12-0.005/-0.01
• Power cable: 2*12AWG(∅ 4.5mm*140)
• Power plug: XT90 male
• Weight:2.0kg

Spec:

• Model:FSESC 28120
• Processor:STM32G071
• Input voltage :DC 7V-33.6V（2-8S Lipos）
• Continuous current:120A
• Maximum current:150A
• Firmware:BLHeli_32 / AM32
• RGB LED Choices :Yes
• Cable Size:14AWG
• Programmable：Yes. Available for throttle calibration, timing angle setting, current detection, telemetry signal, motor rotation direction etc.

Spec:

• 1.8-inch super clear and big screen display
• Display shows more: Except for basic telemetry data, it also display GPS, motor power, real-time temperature of MOS tube, and throttle progress bar information
• Be compatible with Flipsky FSESC/FTESC and other VESC and Non-VESC
• ESK8 mode / E-surf mode switching freely
• Esurf mode：Cruise speed control function
• Waterproof IP rating: IP67
• Bigger remote battery capacity:1500MA
• ESC failure report ：Detect possible failures of the ESC in time for replacing
• Controller mode: PPM/UART
• Charging way:Wireless Magnetic Charging
• VX3 Pro Remote comes with Receiver (support Flipsky non-vesc)
• Support online upgrade firmware

Feature:

1. Replace the communication module with SX1280;
2. The transmitter microcontroller is replaced with GD32F303CGT6;
3. Add FTESC ESC UART control protocol;
4. Add UART, PPM, UART&PPM control modes;
5. Function switching is changed to joystick up and down switching control;
6. Add gear lock function;
7. Add low battery alarm function for skateboards and surfboards;
8. Add total mileage display function;
9. The maximum wheel diameter can be set to 999mm;
10. Add the function of modifying the default gear at startup;
11. Add whether the cruise mode/reverse function is turned on and can be modified;
12. The maximum number of wheel gears can be set to 999mm;
13. Optimize the screen refresh frame rate and faster data refresh display.

Wiring Diagram:

Specs:

• Material:Nylon
• Diameter: ∅120mm
• Pitch: 96mm
• Suitable For Flipsky 65111 motor