Max load : 280 pounds (150 kg), recommending riding weight is 264 pounds(120 kg) and below
Remote: Smart LCD remote with 4 speed modes
Size : 37.4"*10.6"*5.1”( 95*27 *130cm )
The advantages of Flipsky F1 Electric Skateboard :
Samsung battery: brand battery with small internal resistance, large discharge capacity and low heat generation, which is reliable and durable performance.
Smart slide/roll to turn on start; auto-turnoff after 5 minutes no work .
Good stability: 8 layers of maple deck used, which has good elasticity and break-resistant. The perfect combination of trucks and 90mm PU wheels creates a comfortable sliding experience.
Smart LCD remote controller: speed, battery, and range etc, visible to see all the data you need.
The 4 speeds of the remote control are available for users to choose: high, medium and low, and the sports gear accelerates and reacts faster .
Free shipping of this product
By air it takes about 10-18days arrival ;by sea it takes about 25-60 days arrival .
Flipsky FSESC 7550 75V 160A ESC Base on VESC6 With Aluminum Case
-71 in stock
Voltage 14－75V (3－16S safety)
Current:continuous current 50A,Instantaneous current: 160A
Support sensors: ABI, HALL, AS5047, AS5048A
Input source: PPM, analog, NRF NYKO KAMA NUNCHUCK;
Communication ports: USB, CAN, UART;
Motor wire: 12 AWG
Power cable: 12 AWG
Support BLDC square wave mode control and FOC sine wave mode
The CPU adopts STM32F405 with a main frequency of 168MHz and a Cortex-M4 architecture with DSP function;
High current 75V Infineon mosfets in 6 Directfet packages;
Three high-power, high-precision copper current sampling resistors are used to directly measure the three phases current to achieve FOC control and overcurrent protection;
Use TI's UCC272XX series of high-current output gate drivers to drive 6 MOSFETS;
Use three 470UF withstand voltage 100V electrolytic capacitors to ensure the stability of the system under high current drive;
Support with Hall, without Hall, with sensor, and without sensor;
Throttle curves and slopes of all input sources, seamless four-limit operation, count of motor revolutions, ampere-hours, watt-hours, real-time data analysis and readout through the communication port;
The digital VCC and analog VCC are generated by different voltage regulators, which makes the system's AD conversion more accurate;
With the host computer tool software, it can automatically measure the winding resistance, inductance, flux linkage, and also measure the number of pole pairs and other parameters for the motor with sensors;
Adjustable protection measures: low input voltage/high input voltage/large motor current/high input current/over-temperature protection (MOSFET and motor);
High regenerative braking current (separate limit for motor and input), high RPM (different limit for each direction), nearly one hundred setting parameters can be changed through the USB port using the host computer software VESC_TOOL and kept in the ESC;
Wiring Diagram :
Dual FSESC6.6 Plus based on VESC6 With Power Button
-730 in stock
Dual FSESC6.6 Plus(Pro swtich) based on Dual FSESC6.6
Pro switch version:
Power on/off by pressing the button
Added Can bus connector, be more convenient for 4WD set up
Changed the USB port soldering process to SMT soldering instead of manual soldering
Changed the big capacitors to SMT mounting capacitors ,and add more mosfets in the bottom side.
- Hardware: V 6.6
- Firmware: Latest firmware version
- Voltage: 8V - 60V (Safe for 3S to 12S LiPo) for the dual ESC
- Voltage spikes may not exceed 60V
- Current: Continuous 100A single, total 200A , Instantaneous current 400A per single, total 800A for system instantaneous current. values depend on the mounting and ambient temperature around the device!
- 5V 1.5A output for external electronics for single
- 3.3V 1A output for external electronics for single
Dual FSESC6.6 Based upon VESC6 with Aluminum Heatsink
-482 in stock
Big Size Dual FSESC6.6 Based upon VESC6 with Aluminum Heatsink
Dual ESC can reach continuous 200A big current, give your board strong power
One PCBA board integrate two FSESC6 ’s function by internal CAN BUS circuit connection.
The mater and slave board connection can be switched On/Off
Preserve Bluetooth module and RF module connections for both master and slave board
Aluminum anodized Heat sink with fins design for better heat dissipation
size with heatsink: 128.5x91x21mm (L*W*D)
PCB layers: 8layers, thickness: 3oz/layer, total 24 oz thickness
Hardware: V 6.6
Firmware: Latest firmware version
Voltage: 8V - 60V (Safe for 3S to 12S LiPo) for the dual ESC
Voltage spikes may not exceed 60V
Current: Continuous 100A single, total 200A , Instantaneous current 400A per single, total 800A for system instantaneous current. values depend on the mounting and ambient temperature around the device!
5V 1.5A output for external electronics for single
3.3V 1A output for external electronics for single
Modes: DC, BLDC, FOC (sinusoidal)
Supported sensors: ABI, HALL, AS5047
6 shunts in dual system. Each is measurable for the current.