Product Spec:

• Voltage range: 10-24S
• KV(RPM/V): 120KV
• Max Power:8800W,rated power 4400W
• No-load current：3.2A
• Max load current: 150A
• The number of pole: 10(please write 5 pairs when do setup)
• Max torque :13.8NM
• Demension: D70*L165mm
• Max working temperature: 120︒C
• Insulation voltage & leak current: AC500V/10MA/3S
• Lead wires extension: 8AWGx1300mm
• Waterproof level:IP68
• Weight:3.06kg
• Plug: 8.0mm
• Motor wire: 8AWG

Motor drawings：

Specs:

• Firmware: Latest Version
• Continuous current: 100A; instantaneous current: 200A
• Voltage: 14V-60V(Cells: 4-13S; safe for 4S to 12S, voltage spikes may not exceed 60V! )
• BEC: 5V@1A
• ERPM: 150000
• Control Interface Ports:USB,CAN,UART
• Supported Sensors:ABI，HALL，AS5047，AS5048A
• Input Set Support:PPM, ADC, NRF, UART, SPI, IIC
• Modes:DC, BLDC, FOC (sinusoidal)
• Regenerative capacity: Yes
• Programmable: Yes
• Motor wire: 10AWG
• Power cable:8AWG
• Size:75.4x63.7x31.1mm(Including heatsink)

Feature:

1. Support four control modes: Current/Dutycycle/Speed /Position control mode.
2. Using 6pcs SFT01N10T high current MOSETS (100V 500A).
3. Protection functions: low voltage protection, high voltage protection, over-current protection, temperature abnormally protection, mosfets over-temperature protection.
4. Support the function of balancing car by connecting the IMU module through the IIC interface; support inertial measurement unit modules such as MPU9250, MPU9150, MPU6050, LSM6DS3, BMI160.

Wiring diagram:

Please be careful to limit the Absolute Maximum Current below 250A,setting page

Specs:

• Size:L107mm*W103mm*H18.5mm
• Voltage:14-84V (4-20S safe)
• Current:continuous max 100A single,dual continuous max 200A,values depend on the mounting  and ambient temperature around the device!
• BEC:5V@1A
• Support BLDC square wave mode control and FOC sine wave mode
• Firmware: latest (firmware update supported)
• ERPM:150000
• Control Interface Ports:USB,CAN,UART
• Supported Sensors:ABI，HALL，AS5047，AS5048A
• Input Set Support:PPM，ADC，NRF,UART
• Wire Size: 12AWG
• Programmable: Yes
• Regenerative Capacity: Yes

Warm tips:

Detail:

Features:

• Using 2.4G wireless module-E28-2G4M12S, low power consumption, strong anti-interference ability, long remote control distance
• Support 3 speed modes (high gear: red light; middle gear: yellow light; low gear: green light)
• Support cruise control mode
• Remote control and skateboard battery indicator light
• Comfort touch: ABS+Rubber painting surface
• Support reverse function
• Rechargeable Li-ion Battery (850mAh)
• Anti-slip wrist strap
• VX1 Remote comes with Receiver 

Kindly Reminder !
1.Please carefully check following receiver connection diagram corresponding with different FSESC, wrong cable collection in reciver side will cause the receiver burned.

2. The variants (for VESC4/ for VESC6 / For Non VESC) only differenciate on reciver cables , the remote is the same one.

What are the differences between VX1 and VX1 pro?

Receiver Connection Diagram:

For PPM mode(or Non VESC )

For Dual FSESC4.20 Plus:

For Dual FSESC6.6:

Transmitter specs:

• Number of channels:100
• Number of channel groups:1 and 2
• Frequency range:550MHz-590MHz ,antenna 1/4 wavelength
• Audio output level-10dB.
• Headphone output level 87mW(32 Ohms)
• Receiving sensitivity-95 dB
• Signal-to-noise ratio≥90 dB,sound delay 1ms.
• Frequency response 40Hz-18kHz(+/-3dB)
• Reference deviation ±5kHz(-60dBV,input 1kHz)
• Distortion ≤0.5
• Battery type: Lithium battery
• Working temperature 0°C-50°C
• Storage temperature-20°C-55°C

Receiver specs:

• Number of channels: 50
• Numberof channels group:2
• Frequency range :550MHz-590MHz,SNR≥90dB
• Spurious suppression-60dB
• Transmission power 40mW,sound delay 1ms,antenna 1/4 wavelength.
• Reference deviation ±5kHz(-60dBV,input 1kHz)
• Distortion ≤0.5
• Reference audio input level-40dB(Microphone input, 0dB attenuation)
• Battery type: Lithium battery
• Working temperature 0°C-50°C
• Storage temperature-20°C-55°C

Features:

1.Supports two-to-one streaming.Includes intelligent noise reduction.Wireless transmission distance within 100 meters.No delay and anti-interference.

2.Two-to-one: record the voices of 2 people at the same time. Supportsthe use of multiple units in the same location.

3. One-to-one: 1transmitter,1 receiver for use with mobile phone anytime,anywhere.

4.Wind screen included. Built for use outdoors,wind resistant,vibration resistant,effective noise reduction.

5.Come with a built in noise reduction microphone. Also supports use of an external microphone.

6.Support stereo or mono recording modes.

7. Real time monitoring and dection of microphone recording conditions.

8.Built in earphone monitoring funtion.

Video: