1.all these parts in the kit are unassembled when shipment.
2.this All Terrain kit come without motors, it can suitable for flipsky 63 series Motors,recommend motor:6384/6374 /63100 etc . (If you need other KV values, please leave order notes, otherwise 190KV will be sent by default)
Voltage: 14V-60V(Cells: 4-13S; safe for 4S to 12S, voltage spikes may not exceed 60V! )
Control Interface Ports:USB,CAN,UART
Input Set Support:PPM, ADC, NRF, UART, SPI, IIC
Modes:DC, BLDC, FOC (sinusoidal)
Regenerative capacity: Yes
Motor wire: 10AWG
Support four control modes: Current/Dutycycle/Speed /Position control mode.
Using 6pcs SFT01N10T high current MOSETS (100V 500A).
Protection functions: low voltage protection, high voltage protection, over-current protection, temperature abnormally protection, mosfets over-temperature protection.
Support the function of balancing car by connecting the IMU module through the IIC interface; support inertial measurement unit modules such as MPU9250, MPU9150, MPU6050, LSM6DS3, BMI160.
Flipsky FSESC 75300 84V High Current 350A ESC Base On Vesc With Aluminum Case Water Cooling Enclosure For E-Foil Fighting Robot Surfboard AGV Robot
-16 in stock
Voltage:14-84V( safe for 3-20S)
Continuous Current : 50V/300A,75V/200A
Max Current :350A
Supported sensors: ABI, HALL, AS5047,AS5048A
Size:297*115*45mm((Including the height of water pipes and electrolytic capacitors)
The CPU adopts the STM32F405 with the main frequency of 168MHz and the Cortex-M4 architecture with DSP function;
Sensored or sensorless operation + hybrid mode
Configurable RPM-, current-, voltage- and power limits
Input source: PPM, ADC, NRF,UART,PAS
Communication ports: USB, CAN, UART,SPI,IIC
Throttle curve and ramping for all input sources
Seamless 4-quadrant operation
Motor revolution, ampere hour, watt hour counting
Real-time data analysis and readout through the communication port.
Adjustable protection against:
Low input voltage
High input voltage
High motor current
High input current
High regenerative braking current (separate limits for the motor and the input)
High RPM (separate limits for each direction)
Digital VCC and analog VCC are produced by different voltage regulators respectively to make the system AD conversion more accurate
Motor wire: 8AWG
Power cable: 8AWG
Waterproof level(with water cooling enclosure):IP67
Flipsky Dual 75100 With Aluminum PCB Based on VESC For Electric Skateboard / Scooter / Ebike Speed Controller
-60 in stock
Please be careful to limit the Absolute Maximum Current below 250A,setting page
Voltage:14-84V (4-20S safe)
Current:continuous max 100A single,dual continuous max 200A,values depend on the mounting and ambient temperature around the device!
Support BLDC square wave mode control and FOC sine wave mode
Firmware: latest (firmware update supported)
Control Interface Ports:USB,CAN,UART
Input Set Support:PPM，ADC，NRF,UART
Wire Size: 12AWG
Regenerative Capacity: Yes
Phase filering is not available for Flipsky ESC75100 and 75200! Please turn off the phase filter function and choose "false" in vesc_tool when use firmware version on or above 5.3 (VESC_TOOL 3.01). Without turning off the phase filter will result in esc damage. Please do not restore the default parameters when using the wizard interface. Here below video and blog links FYI. YouTube：Click here Blog：Click here
2.4Ghz Remote VX1 Pro for DIY electric skateboard
-29 in stock
Using 2.4G wireless module-E28-2G4M12S, low power consumption, strong anti-interference ability, long remote control distance
Support 3 speed modes (high gear: red light; middle gear: yellow light; low gear: green light)
Support cruise control mode
Remote control and skateboard battery indicator light
Comfort touch: ABS+Rubber painting surface
Support reverse function
Rechargeable Li-ion Battery (850mAh)
Anti-slip wrist strap
VX1 Remote comes with Receiver
Kindly Reminder ! 1.Please carefully check following receiver connection diagram corresponding with different FSESC, wrong cable collection in reciver side will cause the receiver burned.
2. The variants (for VESC4/ for VESC6 / For Non VESC) only differenciate on reciver cables , the remote is the same one.