Max Power: 1380W Max Current: 39A Max Volts: 12S Max Torque:1.1N.m Recommend ESC: 3-12S 50A (FSESC4.12 50A or FSESC 6.6 60A) Weight: 1.05 lb / 0.475 kg The motor length:55.5mm The motor diameter: 49.5mm SHAFT: Diameter 8mm, 25mm length （Recommended: Flipsky 8mm D-shape motor pulley） Motor Wire: 300mm silicone 16AWG wire with MT30 male connector. Wire configuration: Blue = U White = V Yellow = W
BLDC Motor The number of pole: 14 Sensor Wire: Standard RC Sensor Wire HY2.0-5P connector
Direct Drive Motor 6575 58KV With Rubber Tire Wheels
0 in stock
Motor diameter: 65 mm
Motor width: 75 mm
Tire diameter: 105 mm
Tire width: 68 mm
No-load rotate Speed: 2400 RPM
Torque: 2.3 N.M
Supportable battery: 3S--12S Lipo
Max Power: 1000 W
Continuous Current: 100 A
KV value: 58 KV
Remark: The direct drive motor structure
2.Front and rear bridge
3.Four silicone tires
Heat dissipation is better than traditional wheel hub motors.
Power is larger than traditional wheel hub motors.
The torque is large enough to climb a steeper slope and can bear more heavy loading
Installation is more convenient and faster than belt motor.
Bearings also allow for a precise air gap between the motor can rotor and stator as well as resulting in an efficient, low noise motor with long service life.
The motor can protect the internal magnets and provide a solid foundation for the normal operation of the motor to cope with rough terrain during riding.
Silicone tires are used as wheels. The surface of the tires is designed with anti-slip grooves. The suspension holes reduce vibration and the tires are flexible and safer. It is more resistant to wear than PU tires and does not require frequent tire changes.
This is the latest product for direct drive motor systems for high performance electric skateboards.
The direct drive motor uses the best quality materials, you will enjoy the smooth and smooth operation of the direct drive motor under your feet, providing you with greater torque and smooth acceleration mode, providing you with the pleasure of expelling thousands of miles.
All parts will be finished with a Glossy Black Hard Anodize Finish to be durable against the worse of conditions while riding in rough terrain.
High Current FSESC 200A 60V base on VESC6
-2 in stock
ESC can reach continuous 200A big current, give your board strong power
Preserve Bluetooth module and RF module connections for both master and slave board
Aluminum anodized Heat sink with fins design for better heat dissipation
Compact size with heatsink:58x80x15mm (L*W*D)
PCB layers: 8layers, thickness: 3oz/layer, total 24 oz thickness
Hardware: V 6.6
Voltage: 8V - 60V (Safe for 3S to 12S LiPo, Voltage spikes may not exceed 60V)
Current: Continuous 200A , Burst current 800A
5V 1.5A output for external electronics
3.3V 1A output for external electronics
Modes: DC, BLDC, FOC (sinusoidal)
Supported sensors: ABI, HALL, AS5047
Water cooling video test:
Dual FSESC6.6 Plus based on VESC6
-180 in stock
Dual FSESC6.6 Plus(Pro swtich) based on Dual FSESC6.6
Pro switch version:
Power on/off by pressing the button
Added Can bus connector, be more convenient for 4WD set up
Changed the USB port soldering process to SMT soldering instead of manual soldering
Changed the big capacitors to SMT mounting capacitors ,and add more mosfets in the bottom side.
- Hardware: V 6.6
- Firmware: Latest firmware version
- Voltage: 8V - 60V (Safe for 3S to 12S LiPo) for the dual ESC
- Voltage spikes may not exceed 60V
- Current: Continuous 100A single, total 200A , Instantaneous current 400A per single, total 800A for system instantaneous current.
- 5V 1.5A output for external electronics for single
- 3.3V 1A output for external electronics for single