Spec:

• Voltage:14-75V( safe for 3-16S)
• Continuous Current : 200A
• Max Current :300A
• Supported sensors: ABI, HALL, AS5047,AS5048A
  
• EPRM:150000

Feature:

• Regenerative braking
• Sensored or sensorless operation + hybrid mode
• Configurable RPM-, current-, voltage- and power limits
• Input source: PPM, Analog, NRF Nyko Kama Nunchuck
• Communication ports: USB, CAN, UART
• Throttle curve and ramping for all input sources
• Seamless 4-quadrant operation
• Motor revolution, amp hour, watt hour counting
• Real time data analysis and read out via communication ports
• Adjustable protection against:
• Low input voltage
• High input voltage
• High motor current
• High input current
• High regenerative braking current (separate limits for the motor and the input)
• High RPM (separate limits for each direction)
• Digital VCC and analog VCC are produced by different voltage regulators respectively to make the system AD conversion more accurate
• Motor wire: 8AWG
• Power cable: 10AWG
• Waterproof level(with water cooling enclosure):IP67

More Detail:

Wiring Diagram With Aluminum Case:

Wiring Diagram With Water Cooling Enclosure: 

Spec:

Mode : 48V 3.6HP

• Rated power: 800W
• Staring system:Accelerated start 
• Motor : Brushless motor
• Rated voltage(V) : 48 
• Rated speed(r/min) : 3000
• Rated current (A) : 18
• Control system: Tiller control
  
• Maximum speed(KM/H) : 13
• Overall LxWxH(mm): 365x220x920
• Weight:11KG
• Recommended propeller range: 7-1/4x5
• Transom plate height(mm):420
• Battery recommendation:Selection of 30-120A safe storage battery maxium power sustainable 2-8 hours

Mode : 48V 5.0HP

• Rated power: 1200W
• Staring system:Accelerated start 
• Motor : Brushless motor
• Rated voltage(V) : 48 
• Rated speed(r/min) : 3000
• Rated current (A) : 25
• Control system: Tiller control
  
• Maximum speed(KM/H) : 18
• Overall LxWxH(mm): 365x220x920
• Weight:12KG
• Recommended propeller range: 7-1/4x5
• Transom plate height(mm):420
• Battery recommendation:Selection of 30-120A safe storage battery maxium power sustainable 2-8 hours

Mode : 48V 8.0HP

• Rated power: 2200W
• Staring system:Switch knob added 
• Motor : Brushless motor
• Rated voltage(V) : 48 
• Rated speed(r/min) : 3000
• Rated current (A) : 50
• Control system: Tiller control
  
• Manipulation mode: Back
• Rod length(mm) : 910mm
• Weight:14KG
• Total height(mm):1320mm
• Recommended propeller range: 7-1/4x5
• Transom plate height(mm):381-508
• Battery recommendation:Selection battery with a capacity of over 120AH 

Mode : 60V 10HP

• Rated power: 2200W
• Staring system:Switch knob added 
• Motor : Brushless motor
• Rated voltage(V) : 60
• Rated speed(r/min) : 3000
• Rated current (A) : 38
• Control system: Tiller control
  
• Manipulation mode: Back
• Rod length(mm) : 910mm
• Weight:14KG
• Total height(mm):1320mm
• Recommended propeller range: 7-1/4x5
• Transom plate height(mm):381-508
• Battery recommendation:Selection battery with a capacity of over 120AH 

Features:

• KV:160KV
• Max Volts:12S
• Rated voltage:24V
• No-load current:＜ 1A
• Maximum load current:30A
• Rated power :500W
• Motor dimension: 50*62mm
• Thrust ：5KG
• Current:12A
• Hole distance:φ 35
• Screw holes:4×M4
• Waterproof Level :IP68
• Motor wire: 12AWG

What is Advantages of Flipsky 5062 motor:

• Applying high thermal conductive material into the vacuum glue sealing coil for waterproof treatment, which can protect the copper wire and silicon steel sheet from seawater corrosion effectively.
• Adopting special stainless steel bearing and lubricating grease. Salt spray test can reach 144 hours.
•  The upper and lower positions of the magnets have the rings to lock the magnets and prevent the magnet from falling off.
• The motor shaft is made of 316 stainless steel, which can work in seawater for a long time.
•  The solder joints of the motor leads are potted inside the motor, which can meet the 200m suppression test.

Advanced Features:

• ESC can reach continuous 200A big current, give your board strong power
• Preserve Bluetooth module and RF module connections for both master and slave board
• Aluminum anodized Heat sink with fins design for better heat dissipation
• Compact size with heatsink:78x65 (L*W)
• Compact size with cool water case:120.11x72.93x31.45mm(L*W*H)
• PCB layers: 8layers, thickness: 3oz/layer, total 24 oz thickness

Spec:

• Hardware: V 6.6
• EPRM:150000
• Firmware: VESC_default_no_hw_limits
• Voltage: 8V - 60V (Safe for 3S to 12S LiPo, Voltage spikes may not exceed 60V)
• Current: Continuous 200A ,  Burst current  800A
• 5V 1.5A output for external electronics 
• 3.3V 1A output for external electronics 
• Modes: DC, BLDC, FOC (sinusoidal)
• Supported sensors: ABI, HALL, AS5047
• Waterproof level:IP67
• Motor wire: 10AWG
• Power cable: 8AWG

Diagram: 

Water cooling video test:

Product Spec:

• Voltage range: 6-20S (25.2-84V)

• Max Spin Speed(RPM): 16380

• KV(RPM/V): 120KV/100KV

• Max Power:6000W

• Peak current: 200A

• The number of pole: 6

• Max torque at 60%:9NM

• Demension: D65*L161mm

• Max working temperature: 120︒C

• Insulation voltage & leak current: AC500V/10MA/3S

• Lead wires extension: 8AWGx1300mm

• Waterproof level:IP68

• Weight:3kg

• Plug: 8.0mm       

• Motor wire: 8AWG

Package inclued:

1*FS65161 ( 100KV or 120KV)

1*Propeller

3*8.0mm bullet connectors

Why upgrade from oil sealed to water/ceramic sealed)?

Add a ceramic ring in the middle, reduce the direct contact between the sealing ring and the bearing, extend the life of the bearing; improve the waterproof performance

Update Detail:

Water-seal has 2 parts as the following pictures
2 strong hardness ceramic run with each other and metal ring part spins together with shaft&ball bearing,
which can prevent the abration between shaft and water-seal, extend the motor lifespan with better IP rate.

Two shafts size option :

1.12mm shaft with M8x1.25 thread (Sensorless)

2.10mm shaft without thread:

Application:

Efoil, Electric surfboard, Electric Hydrofoil,Foilsurf,Surffoil, RC Boat, Esurf, Jetski, Jetboard, etc.,